Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi Nordic DevZone Support,
I am facing an issue with my custom PCB using the nRF52840 microcontroller and Zephyr NCS v2.6.1 . The same firmware works on other PCBs , but...
Hello, I am working on nRF52840 and using nRF Connect SDK v2.9.0.
I want to know how I can configure the UART to be half-duplex tx or half-duplex rx.
I checked the APIs...
Hello Nordic supporters!
We are developing a system using BT Mesh alongside a software DALI protocol driver with certain timing requirements.
Right now we're trying...
Hello,
I am trying to build the Wi-Fi Bluetooth LE coexistence example using the nRF54L15 DK and nRF7002 EB, but I encounter the following error: zephyr_pre0.elf section...
This is not a support request.
I just want to share some code that others might find useful. If I post it here then they might find it.
The current RADIO_TEST example...
Hi,
I'm trying to use RTC to generate interrupts at every second. The rtc event handler is below:
In the RTC examples, nrfx_rtc_counter_clear is used to reset the RTC...
We are using the nRF5340 with the nRF7002 Wi-Fi module on our custom board. Our application periodically sends data to a server. During continuous testing, we encountered...
nRF Connect SDK with VSCode has suddenly stopped working.
Problems
When I try to create a new application by copying a sample, it says "no samples available".
When...
I created an application that stress-tests wifi scanning and neighbouring cell scanning, on nrf9151 with wifi extension board. Wifi network scanning and neighbouring cell...
I am using peipheral lbs sample and modifying it for my project use. By default it doesnot has pm_static.yml where addresses could have been defined. Once i build the modified...
Hi everybody,
I have problem with my nrf9151-DK. If I switch my kit do AT-Command mode (I use Serial Terminal of Nordic, v 1.4.3), I am not able to switch my kit to PPP...
I'm porting some code from nRF52832/nRF52840 to nRF54L15 using the MPSL timeslot API. The old code uses MPSL version v2.5.1, the new v2.9.0.
The firmware opens a session...
I am evaluating Bluetooth Periodic Advertising with Responses (PAwR) using a NRF52840 Development Board. I am very satisfied with the development environment and the nRF Connect...
Hi
I want to check the nRF54L15 ADC Rsource value
As below pic., P1.07/AIN3 input voltage will be 0.6V (1.8V divider by R429 & R428)
So the Rsource value will be R429...