But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
We are testing the combination of hrs example and the code in the butonless example. When I tried dfu after putting the code together, this error occurred. What does this...
I am trying to interface the microphone with nrf52840 and using the PDM interface. After initializing the module (nrfx_pdm_init) and then set the buffer , I do see clock and...
Dear Sir.
I have some boards that work with nRF9160 and Chipsim.
Some work fine.
Using MQTT application
With two boards I get the errors.
ERROR: getaddrinfo failed...
I am new to the nRF5 SDK. This is my first time using nRFX SPIM so this may well be a beginner error.
I'm using SDK version 17.02 and I am using a nRF52840 module.
I...
Board: nRF52840DK
SDK: 15.3.0
Softdevice: 6.11
I am trying to increase the MTU size in order to read more data on the peripheral. I have tried to increase the NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
The SDK version I use is 15.3. And I tried to add the following code to the ble_nus.c
But it didn't work.There is no characteristic 0x2901. I don't know what's wrong....
Hi, I'm investigating the current consumption of a new product that we are developing and have found
current spikes of 40mA every 24ms. The spikes occurs in unconnected...
HI,
I get confused using the ble terms hence i'll try to articulate my query as much as possible. I'm using the nRF52832 board and all i have one service with one characteristic...
Hello,
I want know what is the difference between the three kind of low power mode?
System ON, Full 24 kB RAM retention, Wake on GPIOTE input (Event mode) System ON...
Hello
I am trying to get the angle of the sensor using the value of mpu6050.
I used a formula to obtain an angle using sensor values. However, if I calculate this expression...
Hi,
I´m using SDK v16 on a custom board and try to implement the wake up functionality of the low power comparator. In order to describe the system as clearly as possible...
Hello.
I am programming the NRF52810 breakout board.
Before I am testing the prototype, I am using NRF52832 breakout board, and it works well now.
However, the same...
Hi Dev Team,
I was working with the nRF9160 and started off with the basic UART sample found here : https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples...
