But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello,
I am experiencing a critical failure while trying to program my nRF5340 DK using the nRF Connect for Desktop Quick Start app (v1.6.0). The process fails at the "Program...
I am having a recurring problem with NFC-CONNECT: build action. It hangs when building. Gets stuck with the following message in lower-right hand corner of screen:
The...
I have successfully installed west and zephyr, and I have successfully build a simple tflite-micro hello_world example, but it just generates the zephyr.hex file. SInce i...
I am using a dynamic BAS service. I have noticed that after a few bt_gatt_service_unregister() and bt_gatt_service_register() calls, the following error occurs: bt_gatt: Unable...
Hi, trying to directly build the solution for the exercise i get this error at the end.
The whole log-output:
Building l5_e1_sol west build --build-dir /mnt/df01dc22-f3bf...
Hi! I am trying to get the samples "Bluetooth: Direction finding connectionless locator" and "Bluetooth: Direction finding connectionless beacon" to work on nRF54L15dk. I...
Cannot program our nRF9151-SMA-DK, we have other boards and work normaly. This is the programmer log:
08:30:21.996
Initialising the bundled nrfutil device
08...
nRF54L15 - ncs 3.02 - toolchain 3.02
I changed my build settings from no sysbuild to sysbuild in order to use serial recovery and/or FOTA. I thought everything was OK until...
Hi,
For my university MEng group project, I am working with the nRF5340 Audio DK and Bluetooth LE Audio (LC3 over ISO).
My end goal is to stream audio from an nRF5340...
hi,
i'm a beginner for nrf9160DK so can you guys help me to how can i nrf9160 up and running for the first time. i'm not able to up and running with this video https://www...
I have a problem where the GPIO pin is not working as intended (it is constantly high but it should be alternating high and low). Via debugging I've ascertained that the problem...
Hello, I am encountering a crash in MCUBoot when using the following configuration:
MCUBoot as bootloader (SB_CONFIG_BOOTLOADER_MCUBOOT)
TFM configuration (build /ns...
I am encountering a build error while setting up a build environment. Can you provide assistance as to what the issue I am encountering may be? I am using VSCode on MacOS...
hi,
i'm stuck at lesson 3 exercise 1 in step 1 so i create an application with choosing option 1 create a blank application for this first task to print hello world and...
Exhausted everything. Here's the guts of the code. A task is called at 2Hz to push the value, which at 1024/s makes an event time of +512. I set the cumulative RPM to +1 for...
