Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hello,
I'm using nRF52832, SDK15.0.0, Softdevice S132.
What should be the code added to application in order to support BLE DFU service?
I've been here , but its for...
hello,
I want to use RSSI on nrf52832, and the project is uploaded.
the question is, I test the RSSI on channel 2468MHZ， the NRF_RADIO->RSSISAMPLE result is about -92dBm...
Hi,
I followed the instructions for Getting Started with the NRF9160, activating the iBasis SIM card, placing into the board and applying USB power.
The first issue...
Hi,
I'm trying to update the firmware on my nRF9160 development kit
I downloaded the modem firmware and DFU tool
And then tried to follow these instructions: ...
Hi,
I want to activate eDRX on mqtt_simple example and measure the current consumption. I guess based on the code, by enabling "CONFIG_LTE_EDRX_REQ" it will be activated...
Hi guys,
I know that there is no official support for C++ on NordicSemi side, but I just wonder if it would be possible to work with C++ in Segger IDE. I'm trying to integrate...
SDK version: nRF5_SDK_15.3.0
Platform: nRF52840 DK
SoftDevice: s140
--
Hi All,
I use ble_app_blinky example and Android nRF Blinky SDK to add new function.
Recently...
Hello,
I'm using NRF52840 module to make a customer device. This device send message by UART. My device is powered with a battery, for this reason I would like reduce the...
Hi All,
We are using NRF52832 in our project. We have implemented the c code to perform nrfutil operations.
We are following below steps to do it.
Erase all files...
Hi, I'm doing some tests with Legacy OOB and I made it work with Master Control Panel 3.10.0.14, but when I try with nRF Connect v2.6.2 it fails. I know MCP is not supported...
Hi nordic,
Please inform bjorn-spockeli to reply in this thread its very urgent
https://devzone.nordicsemi.com/f/nordic-q-a/45470/encryption-and-decryption-of-advertising...
i working on a project of buttonless dfu on nrf52832 dk. so face a problem that after dfu the uart service is not show on nrf connect app. so i not be able to receive data...
Dear Technical Team,
I would like to check the more detals as following from you.
We shipped this part NRF52810-QCAA-R 60pcs to the customer, but they said they found...
There are several topics already exist on this forum concerning the attribute reporting, namely:
https://devzone.nordicsemi.com/f/nordic-q-a/42171/zigbee-attribute-request...
