Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I want to highlight 2 infuriating bugs in nrf connect SDK. I believe it applies to all versions.
1) If you have more than one app in your applications tab, the context will...
Hi I would kindly ask what is the recommended layer stack up for npm1300 PMIC.
In reference designs 4 layer board with 2 internal ground planes is used. Looking at the docs...
Using:
NRF9151
TF-M enabled
NCS 3.2.2
I'm trying to find more space for my heap on the nrf9151 and I'm disappointed that with a minimal implementation of TF-M...
I am currently working on a project where I intend to use an nRF54 chip as a BLE or ESB receiver node to capture JPEG image signals and transmit them to a PC via USB. I would...
hi
After switching the 9160 crystal oscillator to an external crystal oscillator, we found that the power consumption of the MCU increased by approximately 1.2 mA constantly...
Hello,
I created a copy of the nRF Cloud CoAP Device Message sample application for the Thingy 91 X. It builds using the default optimization level. However it fails to...
Hello,
Is there any AT command to enable/disable HW Flow Control RTS/CTS for nRF9151?
I tried AT+IFC=0,0; AT+IFC=2,2; AT+IFC? commands but getting error.
Thanks
Hello,
I come today with an issue that was already reported in other tickets such as:
https://devzone.nordicsemi.com/f/nordic-q-a/126189/nrf54l15-grtc-syscounter-resets...
Hi,
I am using nRF5 SDK v17.2.0 on a legacy product. I have code that looks like this:
When reading the characteristic repeatedly, I sometimes see something like this...
Hello everyone
I am following BLE tutorial on Nordic DevAcademy Last part of BLE shows you how to use the nRF52480 to have a BLE sniffer in the Wireshark I have installed...
It seems like the nRF54LM20-DK is not properly powering LED 0-3. After measuring 0V from TP1 to GND, I opened the board configurator and tried applying "ledcontrol" as both...
Hi.
I'm total noob so please excuse my ignorance. I have a nRF54L15-DK which is obviously not a nRF52 device and the RSSI viewer is only compatible with nRF52 series. But...
Hi Dev,
Development platform: NRF54L15 + NCS 3.0.2. We use k_uptime_get() to obtain the system uptime and perform task scheduling. Everything runs normally when the device...
