Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I'm currently working on integrating modem FOTA updates into my application. I have the FOTA working at the moment, I'm able to go to and from a FOTA-TEST version with the...
I try to run this sample https://github.com/NordicPlayground/fw-nrfconnect-nrf/tree/master/samples/nrf9160/mqtt_simple from the master branch, but when I connect to the network...
I'm connecting the battery to the VDDH 3.6V or 3.7V and sensor to VDD, it means nrf52833 get powred on from VDDH and sensor get the power from VDD. is it ok? please check...
I use the nRF52840 MCU and SDK 16 with S140 softdevice. I want to use spi interface to control 3 SPI slave. They share the same SCK, MISO and MOSI. I use 3 chip select pis...
We're using the IOS-Pods-DFU-Library on an iOS13 iPhone connecting with an embedded device that supports Nordic NRF DFU. We're experiencing some issues with both the nRFConnect...
I have questions related to use of UUIDs. Any help would be grateful.
The following are the UUIDs that are seen from our peripheral device during advertisements and after...
Hi,
I tried to use the exactly same code in the TWI scanner example for nrf52832, SDK15.3. Everything works fine when I flashed only the example code, which has no softdevice...
I am looking for an updated schematic for the PCA10059 v1.2.0. Everything on info center is version 1.0.0. Noticed that a resistor was added (R7) so wondering if there were...
I'm trying to debug issues in my application related to FDS garbage collection.
My application periodically runs fds_gc() from startup. At this point, garbage collection...
Hi
I got a nrf52833 dk and followed "nrf52833_heart" SDK file readme file is success
next step I install segger studio and JLink_Linux_V662d_x86_64.
wend i open studio...
Hi Devzone:
I saw two functions to write the retention register for DFU, nrf_power_gpregret_set and sd_power_gpregret_set.
What's the diffrence between
nrf_power_gpregret_set...
I'm experimenting with multiprotocol support on a PCA10056 (nRF52840) and the S340 softdevice. I need to use BLE and ANT+ at the same time, sending data to either ANT+ or...
What type of cable is required for the debug out, P19?
The specs for the port only say the number of pins, but not the pitch https://infocenter.nordicsemi.com/topic/ug_nrf52840_dk...
nrf52840 packet transmitting time measurement for TOA or TDOA
Hi I’m cu rrently working with the given nordic project “ nrf52-ble-long-range-demo ”
What I’m trying to...
Hello
Where is the the timeout for the Resolvable Private Address (RPA) defined?
only possible in the central?
can I change the timeout in the android nrfConnect...
