I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hello, I want to ask a question. We have a project that needs OTA function. There are two Bluetooth devices A and B.
1. Both A and B are central_and_peripheral
2. A's...
I want to check for an RX timeout after sending a TX.
I am puzzled on how this comes about.
As best I can tell I have enabled TIMER3 for the timeout.
I have created...
I'm trying to create a user defined HCI command for nrf52840 over the Zephyr APIs to be used against Bluez stack on Linux.
I've enabled the CONFIG_BT_HCI_VS_EVT_USER=y....
Hello,
I am trying to accomplish sending a simple ON or OFF command to the coordinator. Is this possible to do?
I have a router device with these Clusters:
It...
I have been converting my TWI calls to be asynchronous by specifying a twi_handler, but my NRF52840 does not sleep during the TWI calls.
I use SDK15.3 and s140 softdevice...
So this is my understanding of the programming process of an external board using the DK.
Pins from table 1 here: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrf91_dk...
Hi,
I want to develop DFU using BLE. I have started with test image given in the example folder.
I have nrf52480 device , using S140 softdevice. I have followed these...
I am unable to see advertisement on the nrfconnect app, when using BLE_GAP_ADV_TYPE_CONNECTABLE_SCANNABLE_UNDIRECTED
However, when using BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0) as a central and Android device (Bluetooth 4.2) as an advertisement.
During development, I was wondering...
Greetings.
We've been developing a product that uses BLE Mesh. We are currently using the Waveshare nRF52840 Bluetooth 5.0 Evaluation Kit for prototyping purposes. As far...
When I try basic usage of NRF Queue library I'm getting the following error:
Undefined reference to `nrf_queue_write'
SDK version is 15.3.0.
In sdk_config.h I've enabled...
Hi Support,
I have tried setting up my nRF52840 Dongle ( https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF52840-Dongle ) PCA10059 as explained in the steps...
Hi,
I've got the gaming mouse dev kit and I'm stuck trying to get it programmed using my nRF52840-DK. See my hardware connection image below.
If I leave the mouse power...
Hi. I am currently using a custom nRF52840 board.
I am able to connect and pair with both IOS and android via BLE. However, the IOS have some issues.
After 45 minutes...
