Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hello,
I'm trying to receive an inverted UART signal on the Arduino Nano 33 BLE (NRF52840). I've been able to invert the transmit signal okay using two GPIOTE channels and...
in ble send data period ,nrf 5340 CPU seem to be shared only by ble send
data ready and data read in ble not send period can equal ,this mean every data come from ecg chip...
Excuse me:
I'm testing the maximum rate of ble_app_uart。
1、Can the nrf connect app on IOS initiate the update of MTU and PHY?How to update MTU and PHY on IOS nrf connect...
I use nordic5340 SPI read ADS1298R ecg data, using nrf5340 p0.13 to connect ADS1298R data ready pin . when ADS1298R data ready pin high to low mean ADS1298R data ready .i...
Hi guys I am new to Nordic, just made a DevZone as the technology isvery interesting to me. So far I have been playing with ESP series but I know nordic is in a class of its...
Hello everyone,
I have been working for a few days with nRF52833DK building a BLE mesh where one of these microcontrollers is a client node or a server node.
However,...
Hi,
I have several questions about the dongle board.
1. Why should the p0.19,20,..,25 be connected to the reset pin?
2. what is the difference between the reset button...
Hi, All,
I saw the options for S2 and S8 in conn.h of ncs, but i don't know how to use it.
And I want to test the relevant data and differences between S=2 and S=8 broadcasting...
Hi Team
In nRF5340 Product Specification v1.1 page 117. The CACHEDATA is mapping as secure. But it have trust zone ID 252. So I have below questions
Does cache only...
This is a strange problem. 10% of our production boards fail outdoors within tens of seconds and will not fail after tens of minutes if indoors . The rest of our production...
Hello,
is there some existing example for nRF52840 DK, that would allow setting my own custom HID descriptor? e.g. "Telephony page (0x0B)" or a custom vendor-specific HID...
Hello,
I'm building a project for a nRF5340 and i need to use the mesh_stack.h library to reset device mesh configuration however every time i try to include it i get...
tutorial followed: https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-characteristics-a-beginners-tutorial
I have followed the above...
