Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
just passed Cellular IoT Fundamentals while I was waiting for my nrf9151dk to be delivered... Now that I have the DK I can't get the dk to be provisioned...
I couldn't get...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
Hello, I have a question about how to monitor Zigbee devices for dead or alive, especially end devices that sleep. I am currently developing a hub to control and retrieve...
Hello, We have a custom board with nRF52832, using BLE, s132. I have noticed recently that in nRF Connect App (v4.29.1) usually the services and characteristics show up twice...
Hi there,
I am trying to develop a simple application that must write information within a micro SD card (nothing too fancy, it is just plain data read from the internal...
Hi,
I added MCUboot and SMP BT Service to the OpenThread CLI routine to implement the device firmware upgrade function.
I found that after DFU is completed, the Thread...
If the lock's status changes while the device is powered off, causing a mismatch between the lock and the Apple Hub, how can I immediately update the status upon powering...
Hi!
I cannot get I2S echo sample to work on nrf54L15. Tried following overlay
build configuration nrf54l15pdk_nrf54l15_cpuapp
I verified with oscilloscope that no...
Hi,
All-of-a-sudden I'm having problems debugging my application. THis morning it was working right, this afternoon it's gone wrong!
I think it's pretty near using up...
Hello,
we want to get three different states using only one GPIO:
1. nRF52840 GPIO output driven low
2. nRF52840 GPIO output driven high (3V3)
3. nRF52840 GPIO internal...
Hello Nordic community,
I'm working on a project using the nRF5340DK where I need to achieve precise control over three GPIOs with the following specifications:
P0.07...
Hello,
We are using the nRF52840 on our own board.
When I added up the current consumption at 3V, based on the datasheet, I get 14.3mA (CPU from RAM, Tx at 0dBm 1Mbps...
Hello,
I'm using peripheral_past sample on nrf5340 audio DK board, and select nrf5340dk_nrf5340_cpuapp_ns for Build Target.
I added the following config to enable RTT...
Hello,
I have nRF9160, modem FW = 1.3.6 and nrf sdk version 2.7.0.
I am trying to create an outgoing socket with connects to specific port num and ip address but I am...
Hello, I am working on a project where we use MCUBoot.
Currently everything works fine, but now we wanted to introduce persistent storage of some key value pairs.
For...
Hi Nordic Team,
What is the difference between 10 bit, 12 bit and 14 bit operation mode and 8/10/12/14 bit resolution in SAADC of nRF54L?
Best regards,
Bhavya
