Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have a custom board where I have an nrf9161 main processor and an nrf54L05 processor connected with each other via I2C.
In this case, I'd like to manage the communication...
I used Nordic52480 DK(bulb) as DUT to run Matter Certification case TC-DGGEN-2.1 .
Steps:
1. setup OTBR on Pi4：./certification-tool/backend/test_collections/matter/scripts...
Hi,
Is there any sample code that can check the Ion_idle8 current below?
I am currently evaluating the following currents on a custom boat and it is running at around...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine if all of the power components are required.
The nPM1300 appears to provide...
Hi
I am trying to setup and test the OpenThread CSL feature on nrf52840DK with OpenThread daemon and RCP mode nrf52840DK.
I found there is a way to build the Daemon for...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
I have set up the OTBR with a RPi 5 and an nRF 52840 DK as an RCP. The CLI device can join the thread network as a child, the OTBR as the leader.( https://www.youtube.com...
Hi there, I am unable to install an SDK through VSCode while trying to take the steps outlined in the documentation. I have navigated to "Manage SDKs" under the "nRF Connect...
Our company is in the process of developing a new IoT product for LTE-M and NB-IoT. The sample application lwm2m_client runs fine on our devkits nRF9151DK & Thingy91 and connects...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hi
I am trying to mugrate my app from v2.6.1 to v.3.0.2.
As I have several configuration variants, so I build from batchfiles, ending in a west build command. Updating...
Hi,
I am currently developing an nRF54L15 module.
During the evaluation, I measured the Tx current consumption and got a result that was 2mA higher than the value listed...
I can flash the chip. I can run the debugger. I can go to the connected devices, select the device, go to the little "plug" symbol on the RTT, and select it. That brings up...
