It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hello
I am playing with the mesh dfu and the distributor application on nRF52840 DK board
I load the image I want to distribute using mcumgr application on a Raspberry...
Hello
According to Enhanced ShockBurst (ESB) documentation , to stop the ESB module you need to call esb_disable(), but it also says that you need to check if the module...
Hello,
We are considering to develop an appliance based on the nRF5340 AUDIO DK.
The nRF5340 AUDIO DK contains the VM3011-U1microphone that is absolute on the market....
Hello,
We’re testing the nRF9160 GNSS performance on our custom PCB and have noticed that, even with A-GPS, the first fix after powering on the device takes significantly...
I am having problems flashing my custom board with a nrf5340 chip. Sometimes it works, sometimes it does not, but more often than not it doesn't work and I cannot figure out...
Hello Nordic Team,
I’m trying to use the nRF54L DK to program an external MCU via SWD , but I’m encountering an error during connection. I’ve already followed this guide...
I'm trying to build the light-switch-app from Matter but I get following errors
I have already tried to reinstall the sdk (I use v2.8.0) and build it just like that without...
After modifying the factory data with the script generate_nrfconnect_chip_factory_data.py, the discriminator and passcode work, but how do I change the value of the Manual...
I am trying to interface an SD card with the nRF9160-DK using an SD card adapter module. My goal is to write the string "hello" to a .txt file on the SD card. I believe I...
Is a TVS diode clamping voltage of 6.5 V acceptable for supplementing the built-in ESD protection of the NRF52840 GPIO pins?
It has been previously established in the forum...
Hello everyone!
I am rather new to firmware development with Nordic products and am experiencing some trouble with the Thingy91 LTE BLE Gateway sample.
What is the problem...
Hello,
I want to set my TTL value in a node (nrf52840 dongle) that i use as a relay node.
In prj.conf file I set the node in this way:
CONFIG_BT_MESH_RELAY=y
CONFIG_BT_MESH_RELAY_RETRANSMIT_COUNT...
Hi , i am trying to use ble channel sounding feature through hci uart with an external host. I am sending CS commands but getting the following error for one of the commands...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
I want to realize the connection and communication between the broadcaster and the upper computer software nRF Connect...
Hi there,
One of the functions of the DECT MAC layer is to allocate radio resources to RDs. According to the standard, the MAC layer does that using special beacon messages...
