Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hi, i am learning with thingy 91 x and nrf9151dk. I made the online courses and succesfully conect to the cloud with the nrf desktop quick start in both devices. Now, i would...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
I can't figure out how to respond to a custom Zigbee cluster command, let alone send a custom response. Is there any example on which I could understand how to send a command...
Hi!
we're just finishing the layout for a custom nRF52832 board. On the custom board we have a connector for SWDIO and SWCLK to flash the firmware. Can we use theese 2 pins...
Hi,
I'm trying to familiarise myself with the available crypto functionality on the 52811 and have managed to get basic AES-128 block encryption working using the ECB peripheral...
Hi,
I am using pc-ble-driver-4.1.1 to receive BLE peripheral Device 240 Bytes notifications. And I used "pc-ble-driver-4.1.1\examples\heart_rate_collector" as starting point...
Hi Nordic team,
we want to connect 2 nRF52840 based modules with Coded Phy S=8 Mode to make an cable replacement (NUS). MTU Size is 244 Byte ,to transmit cyclic 200 Byte...
I am trying to connect the DK to AWS.
I got the AT example working and uploaded the certificates. I managed to update the prj.conf file (and then took quite some time to...
It continue to give "No device available" when I connected thingy 91 to the nerf connect programmer app. I tried turning on device while keeping SW3 pushed but still not detected...
Hi Team,
We are planning use the crypto libraries for our application, just we want to know which library is best for us in terms of speed and memory consumption,
1. mbed...
Hi, I'm almost finished setting up a development environment for nRF52840 DK on macOS. I used the new Toolchain Manager to install everything, and then imported the "peripheral...
While developing our project using NRF9160 , we encounters a hard fault. The screen shot and the map file is attached. Please help us in understanding what is happening from...
Hi, we are using nRF52832 SAADC in differential mode. We have two channels connected.
Inputs are now configured as differential-N and differential-P (PSELP and PSELN). ...
Dear all:
i have a problem about connect distance. My central device is nRF52840 ，peripherals are nRF52810 device。all device Hardware RF performance are good. But,when my...
Hi In continue to Tzvi Kaplan thread and other threads here related to the PDM, like this one:
devzone.nordicsemi.com/.../single-pdm-microphone-at-higher-pcm-sampling-rate...
Dear Team, SDK - sdk version 15.0.0 IDE - Segger Embedded Studio SOFTDEVICE - s140_nrf52_6.0.0_softdevice We are developing our custom application and it is battery operated...
