Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I am trying to send data(rssi+MAC address) from GATT server to GATT client using sd_ble_gatts_hvx(). I added the service and the characteristic into the ATT table...
Hi,
Following the AN 29 "nRF51 Development with GCC and Eclipse v1.1", I cannot import any project on Eclipse for nRF51822:
In step 1.2 "Import existing Eclipse project...
I work for a small start-up. Our products monitor events and communicate via bluetooth with an Android tablet.
We are currently trying to make our custom circuit using...
I'm using
s110_7.1
sdk 7.2
DFU
updating application (application.hex + application.dat zipped) works fine, but when updating bootloader (bootloader.hex+bootloader...
Hi,Nordic support
Circuit design: Unused I/O pins
where can i found recommended I/O end terminal desing of unusing GPIO pins ?
I'd need such as pull-down resistor......
HI, I'm extremely new about Nordic component and device.
I buy a nRF51 DK for start understand hou BLE work, I attach to my pc, the green led power on and my pc know the...
With S110 v8.0.0's size increased to 96K, I'm concerned that my current memory layout is going to prevent me from upgrading to a future softdevice.
It seems that the only...
The function dfu_ble_get_peer_data seems to be declared in dfu_ble_svc_internal.h
but not defined, (not actually implemented) somewhere deep within the Nordic Software Packs...
Folks,
Simple UART communication shouldn't be this difficult. Embarrassed to admit it, but I'm having problems setting up and using the app_uart.c/.h module from the SDK...
Hi all,
I have a working prototype of a service which enables a number of characteristics for the control of motors and relays. The motors work great, and are controlled...
Is it possible for gpiote_event_handler interrupt to get executed while the program is executing code inside timer_event_handler?
These events modify same variables so...
I intend to keep a long running clock in the system and use the app_timers(hence RTC1) in a soft device enabled nrf51822 firmware.
I basically have a minute tick and update...
Hi,
I want to run the experimental_ble_app_uart application on our custom nRF51822 board.
However, I could not find a proper bootloader to start the application. Is...
Where can I find an example of using device manager? The SDK doesn't have anything. I am using S110 7.1.0 and SDK 6.1.0 on nrf51822. I am having lots of problems with iOS...
I try to use Android studio to build nRF Beacon project,but it didn't work ,and there are several error .
the error is
Error:(50, 35) No resource found that matches...
