Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Our mission is prevention the increasing cases of missing persons. We wish to design a positioning device which can track the location of our users for their safety.
...
How we can get to know about the ADC sampling is done. On the basis of the sampling done i want to do furture opration like the stop sampling,Continues sampling. How i can...
Dear Experts,
I am planing to use 52810 to connect to a BLE speaker to play a short 'music'. I checked the BLE services provided in SDK:nRF5_SDK_17.0.2... but seems none...
Hi
I'm developing nRF52832.
I have a question about SPI communication.(\nRF5_SDK_17.0.0\examples\peripheral\spi I don't understand, so I ask questions.)
I want to read...
We plan to use nRF52840 in our new project. But the application is likely to be larger than 500 Kbytes
So we are going to use the only one Bank flash for DFU as in following...
We are thinking of making changes to the QIAA aQFN73 circuit configuration from 5 to 4 and use the REG0 DC/DC. VDDH will be connected to a single-cell Li-Ion battery (3~4...
hi, i am working with nrf52840 and need a stand alone qspi peripheral in the project. what is the straight forward way to get qspi into the code up and running without involving...
Håkon Alseth was helping me with this: https://devzone.nordicsemi.com/f/nordic-q-a/83126/hard-fault-using-twi_scanner-example I accidentally clicked "verify answer" when trying...
Hi,
I have the Power Profiler Kit PCA63511 used on top of the dev kit PCA10040. I am trying to measure the power consumption of my custom hardware implementing nrf52832...
Hello,
I am using nrf52840, SDK 17.0.2, softdevice s140 and also implemented OTA DFU in my application.
I want to save some data lets say admin code in flash. Once I burn...
Hello,
I'm having difficulty getting the GPIO set up in a way that behaves predictably on the nRF9160 DK. As far as I understand it, the nRF52840 is what controls the GPIO...
Hi All! My question is that while using coded PHY is it possible to enable the ACK? In case no ACK receives then retransmission of the same packet to the receiver. Thanks...
I am trying to measure the frequency of the square wave on the ARDUINO_6_PIN on the NRF52840 Dev Kit. It seems like it works well until the square wave goes above 2MHz. Is...
Hi,
I see that in the latest SDK 17.1.0 there seems to be no example for regular UART but only for LPUART.
That made me wonder if there is any advantage in any scenario...
