Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi, We built a nrf52840dk shield that interfaces with an SPI sensor connecting to GPIO_IF4. We require using a voltage translator to translate 3.3V signals into 5V to comunicate...
Hi，
In the NCS V2.3.0 version, I successfully obtained the serial device through the following code and compiled it But when I get the serial device in the same way in NCS...
Hi,
Sorry to be posting a lot about my LIS2DH12 on custom hardware lately. I do believe my different inquiries are to be treated as separate.
My (modified) hardware now...
EDIT: Sorry to be posting a lot about my LIS2DH12 problems lately, as I'm advancing somewhat while I have open support threads. Newest thread is here: In preparation of this...
Hi,
I'm using nRF5340 Audio DK with the audio example code in BIS mode. I would like to set the broadcast name during runtime, and not before compilation. Namely, I want...
Dear support team, We need to integrate DTM function into matter. We have disabled bt, but it still prompts that radio_init failed. Do we still need to disable matter protocol...
We are trying to setup image encryption in our nRF build, for use with BLE DFU.
I see that this is not supported by Nordic, but that there is support for it in MCUBoot....
I want to add the timer sample code to my own project "../src/main.c:11:10: fatal error: nrfx_example.h: No such file or directory 11 | I'm encountering the error #include...
| Host | <---- UART ----> | nRF52833 (central) | <-- BLE--> | nRF52833 (Target) |
I have a requirement where I hope to update the central's firmware image through the Host...
Hi,
I am using the NRF52832 DK version 3.0.0 with a UWB module: the DWM1000 from Qorvo.
I was struggling with the SPI communication to get the Chip ID by sending a simple...
Hello,
I am working with nRF52832 and want to put it to sleep and wake it up with a interrupt from a GPIO. I am using a accelerometer LIS3DH to generate the interrupt. I...
Hi,
We're using nrf Connect SDK v2.4 and have issues when calling bt_gatt_notify() from our main thread. The bt_gatt_notify() function blocks even though we have the CONFIG_BT_L2CAP_TX_BUF_COUNT...
I merged two sensors, BME and BMI, and checked the raw data output through NRF_LOG_INFO. Now, I've added the new merged code to the main firmware, but the log for the BMI...
Hi there,
I have multiple flash partitions defined in pm_static.yml.
I want one specific partition to contain a binary data file so that when I flash the image with J...
