I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi everyone,
I'm experiencing an unexpectedly long boot time on my nRF52840 device using NCS v3.2.0. Could you help me verify if this boot time is normal, or suggest any...
Hello,
We have the following environment:
1) nRF54H20-DK v0.9.1 and our custom board
2) nRF Connect SDK v3.2.1
3) Our simple project for testing BLE
4) nRF Connect...
MCU:NRF54L15，NCS SDK V3.2.4，android 7.0, nrf connect 4.26.1, cannot connect stably.
about 40 seconeds, the connect will disconnect, the android 7.0 side:reason is 0x08,...
Something seems to have broken in my VSC and/or Nordic extensions. Intellisense seems to be working for code, but cannot resolve any of my custom kconfig options.
I use...
I would like to sample a digital IO input from two IO's into the processor internal memory incrementally per every rising or falling edge of each of the signals.
Is there...
Trying to do ADV_DIRECT_IND advertisement.
We are trying to do the following advertisements
// ADV_IND Scannable and Connectable
// ADV_DIRECT_IND - Connectable...
I recently purchased an nRF52832 (XL52832-D01) for a wearables power management project. To test the module I flashed the basic blinky (zephyr). I'm using a ST-Link V2 as...
Hi
Brand new nRF52840-DK (PCA10056 rev 3.0.3, serial 1050245467, sticker on PCB). Never worked.
J-Link OB firmware update fails every time with: "Sending firmware data...
Hello! I am having troubles with my custom board using BL5340 from Ezurio. I have tried to flash it via my nrf5340 Audio DK but realized it doesnt support external Flashing...
Hi,
I am trying to set up a secure boot chain on nRF54L15dk with NCS 3.2.3 and an upgradable bootloader .
My intended boot chain is:
B0 / NSIB
S0 / S1 for the second...
Hello,
I would like to implement Device Firmware Update (DFU) over NFC.
Is this supported, and is there any recommended way to implement it? Are there any examples, reference...
I have two nRF52840DK boards that I was working with recently.
PCA10056 3.0.2 2024.33
I flashed one board with a BLE peripheral device code from the nRF connect sample...
Hello,
I'm using dmic module for sampling audio data from microphone. Recently I updated NCS to 3.2.2 and I started observing the following log: "Failed to allocate buffer...
After an update recently with the nRF Connect for VSCode Extension, it's been unable to find where my nRF Connect SDK is located when choosing a build configuration. It used...
