Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hello,
After updating Visual Studio Code, I started facing an issue with the nRF Connect for VS Code extension. When I try to build my project, the toolchain is detected...
hi,
i'm learning exercise 1 and try to using step 14, i installed a java runtime environment and download cf-browser file but i can't open a cf-browser file on java(TM)...
Hi, I am using nrf5340 and nrf52840 SoC in my devices. I have tested that pairing works with the same linux machine for peripheral uart sample for nrf5340dk, nrf53 thingy...
Hi,
I am experiencing an issue with the nPM2100 I2C communication when using nRF Connect SDK 3.2.3. My hardware is a custom PCB with nPM2100QEAA and nRF52840QFAA
I am...
Hi everyone,
I am currently working with the nRF9151DK using nRF Connect SDK v3.2.3 (Zephyr OS v4.2.99). I am trying to run a basic UDP sample with a Terrestar Solutions...
Using the 54l15 chip, with the NCSv3.2.1 version, the example is compiled using peripheral_uart.
I have been using this environment for over a year now.
1. When I was...
Hi there , would the nRF54LM20A support USB "host" or USB "OTG" using Zephyr stack?
I can see that the device includes the DesignWare OTG USB 2.0 controller ( snps,dwc2...
I have made several Build-Configurations for my device. These are using "Extra Kconfig fragments" and everything works a it should.
Now I saved the Build configuration as...
Hi Team,
I am currently working on the nRF52805 module and have developed an application that supports dynamic service creation (runtime GATT service creation).
During...
Below is the relevant code and log:
SDK：v2.9.1
static void dfu_work_handler ( struct k_work * work )
{
int ret = bootmode_set ( BOOT_MODE_TYPE_BOOTLOADER );
LOG_INF...
Como faço para habilitar o registro de logs do mcuboot para visualizar os logs de atualização DFU no nRF Connect SDK 2.9.2, usando o nRF54L15 em uma placa personalizada com...
Hello team,
I attempted to measure the sleep current on the nRF54L15 DK board, but I’m seeing a very high current draw of about 74 mA.
I built and compiled the peripheral_power_profiling...
Hello,
We are developing a custom board that uses the nRF54L15 chip, and are trying to flash an application along with MCUBoot to allow for OTA updates. When I flash the...
Hi Nordic folks,
I'm trying to get the nrf54L15 in a Fanstel BM15M to go into the system OFF state and be woken up later by a timer. All the documentation I've seen says...
