We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello,
I'm using the NORA-B106-00B-00 (nRF5340) on a custom PCB board. I can program the board, but there is no output i.e. print statements coming out of the board...
I build contact sensor example (use nrf connect sdk v3.2.1, nrf52840 chip) and try commissioning with apple home kit (use homepod mini), device commissioning succeed but cannot...
Hello! I'm currently working on a circuit design where weight and size are critical factors. Could you please tell me the minimum dimensions and weight of this chip? Thank...
I've made a new project as I had to change some hardware than the previous one.
The code seems fine, but I'm not able to load the libraries in the project.
A red underline...
When an ESD shock to the PCBA causes the nrf52840 to reboot, what reset code should we expect to show up with hwinfo_get_reset_cause()? RESET_BROWNOUT?
Using Zephyr NCS...
Hi! I am trying to use the LE Audio application and one of the samples in it, by including the necessary source files, and Kconfigs in my project. On the network core, I am...
As per the doc , when I use a smartphone (the base version is Android 12) to touch the NFC antenna, I should see a pop-up window:
3.Confirm pairing with ‘Nordic_HIDS_keyboard...
Is it possible to promote my project here: complete Zephyr development environment running solely on Raspberry Pi 4 Bookworm OS? If nothing else it does provide information...
Hi There,
During the transmission and reception performance test, I found that the LE1M's maximum sensitivity was only -92 dBm, while the LE2M's maximum sensitivity was...
Hi,
we have a Gateway board that uses the nRF52832 with the nRF21540.
The firmware running on the nRF52832 is a slightly modified version of the HCI UART sample found...
I have a problem with timer 3 of nrf52820.
It concerns a trailing edge dimmer implementation based on timer 3. A gpiote is used to sync the zero crossing.
I use ppi...
Dear Nordic-Team,
I designed a custom PCB using the nRF9151 as the host processor, the nRF7002 as a Wi-Fi companion, and the nPM1300 as the power management IC. The Wi-Fi...
Hello,
I encountered a strange behaviour on a nrf52832 : - I flash a a debug firmware (with debug optim in build config) : I can run debugger and add breakpoints - I stop...
I am developing an application that uses NCS2.8.0.
For FW updates, the nRF52833 USB ACM bootloader is enabled.
However, there are some problem.
My device has a battery...
Hi all hope you all are fine and doing well.
I am trying to use the Soft UART (uart-bitbang.c driver) on nRF52 DK for a low-speed UART connection. The initialization fails...
