Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I want to change the BLE advertisement TX power output.
I can already do it via the prj.conf file,
CONFIG_BT_CTLR_TX_PWR_ANTENNA=-4
but I need to change it on-site during...
I am designing an ultra-low-power BLE Audio TWS board based on the nRF5340 and have followed the recommended hardware design guidelines throughout the project. This is my...
Here are results of running the bluetooth sample central uart, first when built with target nrf9160dk/nrf9160, and second with build target nrf9160dk/nrf9160/ns.
*** Booting...
Hi, I am having troubles with flashing my first code to the MDBT53V module. I am flashing via JTAG cable, from my nrf52840DK using vscode. According to my measurements the...
Hi, We currently update firmware using the official nRF Connect app with a .bin file over BLE, and that works for us.
Our team needs to implement the same DFU flow in our...
Hi,
I am facing a strange NB-IoT connectivity issue with the nRF9160 in Dammam, Saudi Arabia.
Setup
SDK version: v2.5.0
Toolchain: nRF Connect for SDK VSCode...
Hi all,
Due to wrong pin assignment on my PCB I am currently bit banging a uart on two P2 pins using the FLPR core. The read bytes and bytes to send are communicated via...
Hello,
after a longer time, I wanted to use nRF Connect for Desktop again, to figure out what exactly my device under development is advertising. I upgraded to the latest...
Back in SDK 17 or so there were code samples for both the client and server side of the LED button service.
What happened to the client/central example when you migrated...
Description
I'm working on a battery-powered application where WiFi needs to be shut down between cloud sync intervals. I'm following the same pattern as the wifi/shutdown...
Hi,
working with nRF52840 with S140 v7.2.0, not sure about SDK version. VS Code + ARM GCC + LD Gold linker.
I changed stack and heap sizes via __HEAP_SIZE and __STACK_SIZE...
We are experiencing an issue with high current consumption when using the nPM1300 powered by a battery. In Hysteretic mode, the battery current draw measures 109 µA. However...
Hello Nordic Team,
We are currently working with the nRF54LM20B device and would like to understand whether Bluetooth Channel Sounding is supported on this SoC.
Specifically...
Hi：
What is the maximum number of targets that a DFU distributor can support for simultaneous upgrade, and what is the upper limit? I haven't found any detailed explanation...
I'm trying to put my code on a RAM/ROM diet and cut out any extra cruft so it will fit in an nRF52832. It used to fit with older SDKs, but not with the newest (v3.2.3).
...
