We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello,
I am in the process of following a series of tutorial videos on driving an LED with pwm, but I don't understand how to properly configure my .overlay file and my...
Hi,
I am developing an application for an nRF52840 using nRF Connect SDK v2.9.0. The application currently uses the Zephyr driver for simple PWM functions on several GPIOs...
Hello,
I'm using 'nRF Connect for Desktop v4.2.0' and 'nRF Connect SDK v2.3.0' on windows 11.
I was using vs code well for developing nrf52840 board.
But, I found...
Hi!
How do you recommend to debug crashes?
Especially how do you recommend to debug crashes that happen to our customers that we cannot reproduce?
So far I have been...
Hello!
I'm currently testing writing and erasing data to an external Flash using an nRF5340 and a NOR Flash, the mx25r64.
I'm going to use the SPI_FLASH example.
I bulid...
Hi,
I need to read 16-bit values from a sensor using SPI on the NRF52840. However, since the SPI peripheral only supports an 8-bit word length, what is the best way to handle...
We have nRF5340 LE Audio dks. We intend to check the PDUs transmitted. Does wireshark nrf sniffer support this if yes then how and if not then what is the possible way to...
Hello I want to operate one RGB LED SK6805-EC10-100 for that i need to write data bit by bit in between need to use some delay if any API is there please let me know.
...
Hi,
I noticed that the f_sector_cnt element of the fcb struct is a uint8_t .
How is that supposed to handle large flash sizes? I mean even with a sector of 64KB, the FCB...
Hello Nordic Semiconductor Community,
I am currently working on a project using a custom board based on the E73-2G4M08S1C SoM, which features the nrf52840 chip. For flashing...
I'm studying with PCA10059, Keil through SWD.
Trying to customise BLE_PERIPHERAL_BLINKY.
I have changed the ble_lbs.c/ble_lbs.h,including file name / service name and...
Hi
What is the timestamp accuracy of the nRF51 DK based Sniffer, nRF52 DK based sniffer,
I want to measure the actual accuracy of my advertisement interval, preferably...
I’m working on a device using a Nordic chip and the following setup:
nRF Connect SDK : v2.5.2
Toolchains : v2.7.0
We need to minimize current consumption during...
Hi,
I updated my NCS to V2.9.0, I try to build my project, but it fail(it's OK at V2.8.0). the output message (attached file); Please help to check the message , how can...
