Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
We ran into an issue when trying to use mcuboot on nRF53 with an external QSPI flash. In hal_nordic/nrfx/drivers/src/nrfx_qspi.c, the function nrfx_qspi_write has the following...
dear all：
I want to know how many beacons can be scanned by a gateway in the application of beacons.
At present, we have only actually tested more than 100 tags that scan...
Hi, Nordic Team. I'm using BC805M EK (nRF52805). In my code, I'm using SAADC (PPI interruption), TWI, BLE and System ON/OFF button .
Q1) I don't need RTS, CTS on the UART...
Hi
How to control two channels separately with one PWM instance?
I want to turn on/off the PWM output of each channel with any interrupt process.
app_pwm_disable() and...
Hi,
I am using nRF52840 , SDK 17.0.2/ble_peripheral. I am integrating Mesh SDK 5.0.0 libraries with ble_peripheral libraries in the nRF SDK 17.0.2 as per the documentation...
I created my first nRF52832 custom PCB board and I am having issues with poor RF performance. My project uses RSSI to estimate the distance between a peripheral and a central...
1.For example ,i have provisioned a few ble devices and added to the network by using an android phone .
Is it possible to do the provisioning with other android mobile...
Hi
I am using fds to store log in flash, after reading all data from flash, I am deleting record from flash.
But I found that Record ID incrementing from previous Record...
Hello,
I am creating my first bluetooth application and am having difficulties figuring out the interrupts. The application is working and is very simple - please see pseudo...
Hi everyone,
I have a fairly simple use for ADC: sample 4 channels (scan mode) every 10ms and store in RAM.
Every now and then (asynchronously) there will be a function...
Hello,
I am currently having issues with storing structure data in nRF52840 DK external flash. The default QSPI example present in peripheral sections work fine. But in...
Hi,
We are developing an IoT product using the nrf9160 controller. In the schematic of nrf9160 DK, they connected Ferrite Bead FB2 ( BLM15AX121SZ1D) to pin 101. please check...
Developing a peripheral which supports multiple connections.
It's a pain to have to use loads of devices as centrals - is it possible for nRF Connect (Android) to make multiple...
I'm using bsdlib (v0.7.7) on nrf9160 without Zephyr. Our products are working fine in the field, but so far you need to specify the host by IP address. I'm trying to implement...
