Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
We're using nrf Connect SDK v2.4 and have issues when calling bt_gatt_notify() from our main thread. The bt_gatt_notify() function blocks even though we have the CONFIG_BT_L2CAP_TX_BUF_COUNT...
I merged two sensors, BME and BMI, and checked the raw data output through NRF_LOG_INFO. Now, I've added the new merged code to the main firmware, but the log for the BMI...
Hi there,
I have multiple flash partitions defined in pm_static.yml.
I want one specific partition to contain a binary data file so that when I flash the image with J...
Hi all,
I am developing a project with the nRF52840, using nRF Connect SDK 2.6.1 in Visual Studio Code.
I need to be able to compute an MD5 checksum for a dependency....
Hello, We have one of our products developed using the nrf52805 Module & nrf5 SDK . (which is already fully functional with our application ) Since we have few production...
Board : Nrf52480 custom board
IDE: VSCODE
NRF version : 2.6.99
Zephyr Version : 1.6.0
Segger systemview: 3.54
I followed the instruction from Zephyr RTOS, for using...
Hi support Team,
I would like to know the SDK version to be used for nRF54L15.
Is there any link to know details regarding the configuration, flashing and example codes...
I want to advertise a custom service so my central can filter for it and have a device name and manufacturer. I have the following code but can only seem to do either the...
Hi all,
I want for confirm my findings concerning ERASEUICR. I want to be able to erase the UICR from inside my firmware for automatic testing purposes (no debugger is...
I think I have a failing PPK2.
I tested it with this circuit.
My DVM shows the correct current flow - 1.48 mA. The PPK2 shows 40 micro Amps.
Note that the battery...
Hello,
Using nrf9131-ek because the nrf9161 doesn't seems to have the capability of using an external RC oscillator.
Plans are there in the project with using some/many...
Hello,
Using nrf9131-ek because the nrf9161 doesn't seems to have the capability of using an external RC oscillator.
Plans are there in the project with using some/many...
i have used this case:devzone.nordicsemi.com/.../using-swo-with-nrf52-redux and add ENABLE_SWO but when i flash and use jlink swo viewer,it will have this problem.
...
Hello DevZone!
I am using a nrf5340 with the nrf Connect SDK v2.6.0. I have been running into an issue that has come up a few times on separate occasions. Basically, for...
