Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I have code working for interfacing the nRF52 DK board to a SSD1309 based 2.42” OLED display.
The problem is with getting the correct indexing for lines and columns.
Can...
Hello,
we are experiencing rejection from the network by receiving cereg notification. Modem afterwards stops attempting to connect to network. Which results in application...
I had used nRF52840 DK sometime ago and successfully tested it with different codes. But now when I connect the kit to the PC, it is not getting detected by the same PC that...
We just ran into an issue with multiple build names for nRF Connect's plugin for VSCode on Mac.
Start with "Launch build_a", "Launch build_a_v1", and "Launch build_a_v2...
Hi, here comes a few VSCode plugin bugs, it's really the first one that is the main one, but thought I might as well "dump" the rest of the quirks and bugs I have with it...
Hello,
I am unable to see my Nordic Thingy 53 using the nRF connect desktop app, I can use the apps on my phone, but I need to be able to use my computer for a class....
Hi Nordic Teams:
I'm using Nordic Connect SDK v3.1.0 and nRF52840, I want to update USB iSerialNumber string in hid-keyboard samples.
I tried two methods but they didn...
Hi,
I'm not able to flash nRF54 DK. Log as below:
2025-08-29T06:47:39.828Z INFO Initialising the bundled nrfutil device 2025-08-29T06:47:39.874Z DEBUG Started watching...
*Note that this is only an issue when the central and peripheral are simultaneously active.
This is my current setup for starting advertising, but it requires a deprecated...
Intro We are using the nRF9160 with sensors we manufacture. The code developed is based on the serial SLM sample, toolchain v1.6.0. I am trying to keep the code/project files...
Hello. I have an issue with my development board. When attempting to recover the board, i cannot due to access port protection. This is the specific error message from the...
I'm new to developing nRF devices. This is the first time to set up SDK.
I installed Toolchain Manager v1.2.6 to install SDK, but it is too slow and falls into error. It...
am trying to mount little fs example with my external flash winbond w25q256 but my nrf52840 board taking internal memory and am using qspi
it get automount and writing in...
Hi Nordic,
I need to build an Auracast broadcast speaker (LE Audio BIS broadcaster). Besides audio, I also need two-way data exchange between the Auracast source and the...
Hello,
I am trying to have my own BLE advertising and scanning (with filtering) custom service (from now on peer service) in parallel with BLE mesh. So far I've been able...
