Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello
I am working on integrating https client functionality to product based on nrf9160. My current setup consist of nrf9160DK and nrfConnect SDK v2.5.0. Build is performed...
Hello everyone,
I'm using the Bluetooth peripheral sample and I'm in a scenario where I want to connect to my board from only one device at a time, meaning I don't want...
Hi all, I am working on an nrf5340 and I activated the FileSystem Backend log to save the logs in my external Flash. It's working how we are expecting to except once the flash...
Hi,
I'm experiencing high packet loss with the application nrf5340_audio example, I'm using nrf5340 audio DK as a unicast server, and then I'm using a Sony phone to connect...
Hello, I am using nRF52832, nRF5 SDK, s132, and DFU-OTA with private keys and secure bootloader I am trying to enable the DFU Downgrade by disabling the define NRF_DFU_APP_DOWNGRADE_PREVENTION...
SDK:11.0 Example:ble_app_hrs\pca10040\ s132_with_dfu
Hi Does nrf52810 only support a maximum of one central connection at the same time? If I currently want to connect two...
We wanted to understand better the use of external NOR Flash for nRF9161 applications. For example, in nRF9161-DK, this would be the GD25WB256E chip.
For modem delta fw...
Hi!
I just succesfully flashed my modem firmware to version 1.3.6 using the nrf programmer and a segger external programmer. I can still connect over the serial monitor...
I used nRF52840 board with SDK 17_1_0 ,
I want to used WS2812B in my project so any one can give me reference code for this or
can suggest me how can i implement its driver...
Hi,
I am using nrf52840 and SDK-16.0. Initially I was using SPI1 and SPI2. now along with this I am using SPI3.
we have added new feature which consumes 316*9*26 bytes...
I am trying to cancel a pending connection as a workaround for .
However when I run:
```
LOG_DBG ( "Peripheral connection timeout cancelling and trying later" ) ;...
Hello . I saw this issue raised previously but with no resolution so here it is again
I built the smp-svr sample in VSCode with Zephyr SDK 2.6.1 which produced a DFU package...
Hi all,
The question is about 125kbits and 500kbits long range modulation in proprietary protocol. I'v seen a post saying that is technically possible ( ).
But is...
Hello,
I have a project in progress with an NRF52840 chip. I was able to buy an aircard with the same chip www.kickstarter.com/.../aircard-find-your-wallet-always With this...