Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using nrf52833dk and download nRF5_SDK_17.0.2_d674dde when i build the code the code the following error occur
asBuild target 'nrf52840_xxaa' compiling SEGGER_RTT_Syscalls_KEIL...
I have an "old" nRF5340-DK which I use to program an external board I am developing. I have no problem with the J-Link/SWD connection to my external hardware using the J19...
Hello Sir,
I will use Nordic nRF52 series(832 or 840) to develop smart bluetooth device. As I need to store mp3 audio files in external flash and then will play mp3 audio...
Hi,
In our use case we act as a peripheral and a phone is connected. We transmit lots of data using a protocol on top of the Nordic UART Service. All data is sent using...
Hi,
I have two questions as below. Thank you.
1. Oversampling + burst mode only can use on one channel, can't support two or more channel. Is it right?
2. If Q1's answer...
HI,
We have developed our product with nRF52805 chip using its reference design (Dongle).
Can i use QDID ( 138610) for my end product certification for Bluetooth SIG?...
Hello,
for some days now, my modem is unable to connect to the network, it gets stuck in searching and i don't know why?. I am using an eSIM card from iBasis and i am trying...
I'm starting a new project and are looking for a way to sync data and events between threads.
I have found the event manager and Zephyr FIFO, Queues etc.
I can't see any...
I'm using <TWI Scanner> example on nRF52 DK to find my sensor's address.
According to the sensor datasheet, the sensor's address is 0x21. However, < TWI Scanner > finds...
Hi!
I'm having several problems with skywire nano modules and its development kit, I'm working with three different skywire nano modules (version A x2 and version C). And...
Hi Support team,
I installed the nRF connect sdk & trying to compile the HCI UART project for nrf52840DK, But stuck with some errors.
When I select Build configuration...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I have a question about the maximum number of characteristics. I searched DevZone for the same question...
Hello!
I've just updated from v3.7.0 to v3.8.0.
Devices discovering seems to not operate. (two nRF52840 dongles are plugged in).
Programmer 2.0.0 output looks like...
