Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Dear All.
Using, for instance, a peripheral nRF52840 SoC, would it be possible to change in real-time the text string being advertised, among several prerecorded ones, according...
Hi,
I am following the tutorial to implement the serial recovery on nrf52840DK https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-8-bootloaders...
Hello,
Im using SDK 15 ble pheripheral and central uart example on my custom nrf52832 board.
I would like to know how to set MIN_CONN_INTERVAL and MAX_CONN_INTERVAL for...
Hello,
I would like to send a reason code when disconnecting the client (nRF9160DK) and server in MQTT. How can I do this?
It seems that there is no argument to specify...
When I use nrf_dfu_mbr_copy_bl to do bootloader updating, the data is copied sucessfully, but I find some flash data are updated from 0xFE000 and 0xFF000：
The data is the...
I’m working on a BLE-based door sensor project and my focus is to optimize power consumption for maximum battery life. The code I’m using is designed for a beacon using sdk...
Hi,
really new to the Zephyr stuff and Nordic micros. I've been through the dev academy training examples and get how to use GPIO and I2C by getting a pointer to a device...
Hello,
I wanted to implement a bootloader on nRF52840 which is having 1024KB flash and 256Kb RAM. Can i get any link or tutorial on this if yes can anyone reply to this...
Hi all,
I've been trying to get the samples/sensor/lsm6dsl example working with the nrf52840-based Xiao BLE Sense and have had no luck.
I guess that it's due to the power...
Using NCS 2.5.1. nRF52832 being updated using external flash.
We're having an issue with DFU's on a product that is using a high percentage of the application space (~97...
Using nRF9160. Using NCS 2.6.0. Building for the nRF9160DK with nRF9160. We were wondering if there's a way to enable both the shell and serial bootloader on the same interface...
Dear All.
While trying to complete the DevAcademy course on nRF Connect Fundamentals, using the nRFCommand Line, the VSC, and the Extension Pack to configure the correct...
Hi,
I'm looking to send short data from my mobile phone to the nRF5340 via NFC. I've been searching for examples in SDK 2.7.0 but haven't found a suitable one yet. Now,...
