after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
When advertising using BLE and using the nordic app, it seems that the advertising address changes after every reboot even with CONFIG_BT_PRIVACY set to n. However, this only...
Hi,
we are using nrf52 DK and our custom mobile application. We are trying to collect 15000 sensor samples and finally we are trying to send array to mobile app via BLE...
I suspect there is a bug in the https_client sample. sdk-nrf/samples/net/https_client/src/main.c
The certificate seems to always be provisioned and
mismatch = modem_key_mgmt_cmp...
I have tried to use the power profiler and I got the notification that my firmware had to be updated. I clicked proceed and the device started updating.
When the update...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am using NUS to work with...
My Android app builds and runs fine under Android 13.
But on Android 14 when I try to use the DFU library (ver. 2.5.0) I get the following run-time error: One of RECEIVER_EXPORTED...
I have two nrf5340 audio DKs running bidirectional audio over Bluetooth. Software is modified Audio example from SDK 2.7.0. I am trying to run external i2s in the unicast...
Hello,
I am currently programming using SPIM+Timer+PPI(via nRF Connect SDK v.2.6.1), but due to my lack of understanding, handling handlers is challenging. Therefore, I...
Hello! I am using the nRF5340 dev board with an nRF7002ek wifi shield to connect to MQTT using the Zephyr MQTT library and MQTT 3.1.1 (the only supported version by Zephyr...
Dear Nordic Team, I am currently working with 2 Infineon IM73D122V01 PDM Mems microphones to obtain stereo data, One is configured as left and the other is configured as right...
Hi,
We have 2 projects where we are using the nPM1300.
In both cases we have peak currents.
In de documentations I thought I read some where that the current limit was...
Hello,
this is connected to the question:
For our application I need all radio on/off events. The sample "connection event trigger" sample only gives one trigger per connection...
Hi Nordic,
I am implementing a micros() in the arduino using nrfx driver.
Below is test code and I got some questions.
[Question 1]
Timer 1 and Timer 2 works...
