after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
1. Does the P1.02 (NFC port) on the nRF54L15 support PWM? 2. If it does, please provide the overlay configuration method and sample code.
Best regards,
Peter.Mi...
Hello,
I am building an example app that uses MbedTLS and non-offloaded sockets, because offloaded ones do not fit my needs - updating security credentials needs disabling...
I get the following error when trying to program the device:
The log shows this:
2025-12-10T09:08:50.194Z INFO Initialising the bundled nrfutil device 2025-12-10T09...
Hello,
we have an nPM1300 EK plus the profiling adapter board and are trying to profile some of our batteries.
We have already successfully completed profiling for...
Hello, I am currently struggling with setup and configuration of firmware for nRF5340. The idea is to use two stage bootloader setup, XIP split to external flash and build...
when trying to implement ISR for writeprotect and powergood pin it throws error code 134 which corresponds to not supported.
call stack for reference.
What am I...
I had a fully working BLE setup on my nRF52 (Zephyr), which worked fine on older Android versions. After updating a phone to Android 16 (tested on Google Pixel 7 and Samsung...
Hi, Nordic support team!
I'm having trouble downloading the NCS in China.
The command nrfutil sdk-manager install v3.2.0 --region cn fails with a SHA512 checksum error...
I have designed a custom board using the nrf54l10 chip (similar to nrf54l15). I want to use SPI to communicate with a sensor. So I assigned the pins P2.6 for SCK, P2.4 for...
Hi,
I am trying to communicate with Serial LTE Modem application running on nRF9151DK through SLM Shell sample running on nRF52840DK.
I am using nrf connect in vscode...
Hi,
I am debugging a program running on the FLPR core on the nRF54L15 development board. I need to call a static library (. a file) on the FLPR core. I use the project created...
Hi:
I connected PPK II with nRF52DK.
PPK 2 is connected to the PC via the PPK 2's USB Data Power port.
The led of both are ON.
I see PPK2 in NRF CONNECT FOR DESKTOP...
Hello, I am debugging a program running on the FLPR core on the nRF54L15 development board. I need to call a static library (. a file) on the FLPR core. I use the project...
I am working Exercise #2 in Lesson 1 and the Screen shots and notes about using nRF KConfig GUI do not match what I see. I am using SDK v3.1.1.
The view I see when I open...
My product is very similar to the PCA10056 and uses NRF52840 and Soft Device S140. The firmware uses NRF5 SDK 17.1.x.
I am trying to set up a periodic scanning feature....
