Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I have a Thingy91 that I want to connect to nRFcloud. Not knowing the state of its keys/provisioning I followed the procedure to generate just-in-time keys (as a first attempt...
Hello all!
I'm starting development of BLE Mesh network as part of my Master thesis, for which I designed a custom board based on nRF52832 and nRF52840 with some built-in...
I am working on nrf52840 using nrf connect sdk v2.0.0 example periodic_adv, nrf52840 is prodcasting extended advertising, my app is running on Sony Xperia 1 with bluetooth...
Hello Nordic Community,
I'm now struggeling for quiet some time with trying to get the Keyboard HID example to work with the nRF52840 Dongle.
I already read the complete...
Hi , Nordic and all .
I try to develop uac and hid Composite Device, but i can't find any example about Composite Device in NCS , can't everybody help me .
Thanks very...
Good day
I have been trying to incorporate the WS2812.c from the zigbee lightbulb example (no soft device) with the BLE_Blinky example (with soft device) SDK v 17.2 PCA10059...
Hi. We evaluated the nRF Distance Measurement result with sample 'samples/bluetooth/nrf_dm' of nRF Connect SDK 2.0.0. hardware is two nrf52833dk_nrf52833 board. Below is a...
Hi Nordic,
nRF5 sdk for mesh 5.0, s132, SES
In the mesh network, there are transmitters and receivers. The receivers only receive messages and there are no messages to...
Hey guys,
I am using mesh->provisioner_nrf52840 example flashed in one board, and mesh-> light_switch_server example flashed in another board
I could able to read the...
Hi, I am using an nRF52833dk and my project needs usage of Virtual EEPROM / emulated eeprom over flash memory. I could see that nCS-Zephyr provides a driver at the SDK "v1...
I am trying to build an application where the device scans and on receipt of a packet with certain data in it, advertises for a short while, using both advertising and scan...
I am using NRF SDK 15.2 SDK for development , Im trying scan more beacons ,
static ble_gap_scan_params_t m_scan_param = { .active = 0x01, .interval = 0x0100 , .window =...
Hi,
We have an existing design that includes the nRF52832 and we would like to add the nRF9160 to the design. Does the nRF52832 support coexistence with the nRF9160?
If...
Hello,
We found that the nrf52840 cannot properly pull the CS pin high to get the MX25R64 into DPD. The SDK version is nrf connect SDK V2.0.0. The macro CONFIG_PM_DEVICE...
