Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Setup -
1. Zephyr 2.7.0 for firmware build .bin file and signed using imgtool.
2. Working phones - iPhone, Custom Android ROM (Android 12).
3. Not working phones - Xiaomi...
I following description of https://github.com/NordicSemiconductor/pc-ble-driver#Compiling-pc-ble-driver-from-source to build pc-ble-driver
pc-ble-driver\build> cmake -G...
Hello,
I'm trying to determine the actual used data rate for the coded PHY but cannot find the corresponding API / data structure / enums.
Am I missing something? Can...
Hi!
I have the Actinius Icarus board pre-loaded with the Actinius asset tracker firmware.
Lets say I instead want to load the Nordicsemi asset tracker firmware on the...
Hello,
We have been having strange issues with the watchdog on some of our development devices. The issue is that it seems the watchdog will sometimes not properly reset...
Hello,
I'm currently trying to convert the SPI example project for NRF52811 for the EVK BMD-360 and ran into an issue.
I'm using segger embedded studio 5.42a and nrf sdk...
Hello Nordic Dev Zone,
I have been developing on the nrf5340pdk and recently switched to the nrf5340dk.
I utilized the COM console output for app/net cores via the `minicom...
Good day,
I have successfully implemented exercise steps 1 to 5 of Exercise 2, Lesson 3 of the DevAcademy "nRF Connect SDK fundamentals" course, that deal with "adding custom...
Hi,
As i2c communication + computation takes 45ms in my timer interrupt that happen each 100ms and gave issue with SD, I decided to set a flag in the interrupt and execute...
Is there a configuration / sample available of mqtt simple to talk to the mosquitto server using an authenticated client on port 8884? I saw a message on here that was about...
Hi,
I want to get the GPS value from A- GPS continuously.
Meanwhile, if there is any new application firmware version update,
I would like to download the image with...
I see the problem here. use the dfu-util command in the window system
and i tried many methods and failed The following is my reference website
http://zadig.akeo.ie...
I've been playing around with some code that puts my hardware into System OFF mode to save power, and then will exit this mode and start up when one of three different GPIO...
Hi,
https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink
I have tried the example you modified. It works fine. However, I get ERROR 17 NRF_BUSY when 2-3...
