Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I am working on a smartwatch PoC using the nRF7002 DK (nRF5340), and I am trying to interface a 1.8" ST7735 SPI TFT display (128x160).
Hardware: - Board: nRF7002DK...
Ultrasonic welding is commonly used to seal plastic enclosures for electronic devices. 32kHz crystals can be damaged by this type of welding and manufacturers recommend not...
Does APPROTECT supersede SECUREAPPROTECT or do both need to be enabled for maximum security?
Similarly, do the HW protections (APPROTECT, SECUREAPPROTECT, ERASEPROTECT)...
I am trying to measure current on a nRF52 DK v3.0.0 using PPK II in source mode.
I cut SB9 and soldered SB12 as described in this guide: https://docs.nordicsemi.com/bundle...
Hello , I 'm trying to use the Lan865x (two -wire eth click ) chip with the nrf52840dk board , using zephyr 3 . 7 . I 'm getting always this error while trying a net sample...
Hello!
I've been trying some of the solutions around these forums but I can't seem to get my nRF52840 DK to show up on my device manager so I'm unable to flash anything...
NCS 2.7.0, NRF52840, SYSBUILD with MCUBOOT
We have 1 specific board which is failing with a hardfault and assert MPSL ASSERT: 112, 1617 it occurs whenever we activate...
Hello Nordic Team,
I am using nRF Connect SDK v2.9.0 with the nRF52833 controller. I am currently working on OTA implementation.
I am implementing OTA in another code...
I want to prototype an Auracast transmitter, with an analogue audio input, which is also WiFi enabled. I have read that the recommendation to get started with the nrf5340...
i'm measuring approximately 1.5uA (at 3V3) when sleeping between BLE advertising events, using a program based on one of your the standard examples.... as an experiment, i...
There expect to be a physical limit to the number of components an AHB can support.
For instance, if 8 different masters (Including App core, Net core, several peripherals...
Hi Dev,
Development platform: NRF54L15 + NCS 3.2.3. We are using the GRTC SYSCOUNTER as a system timestamp. Under normal conditions, a software reset does not clear the...
As the title, I have already tested the ESB routine (esb ptx Sample/esb prx Sample) by using nRF54LM20-DK + nRF54L15-DK. There was absolutely no problem. But when I added...
Hello,
I have a project in Visual studio code and Nrf connect.
MCU is a NRF 52833.
For the certicications, the lab request me the DTM mode.
I tried the use the Sample...
