Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello
We check the current in system off in PCA10059 board. and use the ble_app_template application.
If set the VDD 3.3V, after the system off, measure the current is...
Hi Team,
I want to connect power pins on the nrf52840 chip in the schematic.
I find there several VDD pins, how can I select and connect them?
Best,
Gaosheng
Hello,
we are currently developing a customer product based on the nRF9160 SIP.
The requirement is to send the battery voltage periodically over the CoAP protocol (PUT...
Greetings , I have implemented an application with freertos (sdk 15.3) which goes into low power and wakes up on two irqs (rtc and button). When the button irq arrive turns...
We would like to use nRF9160 has MODEM only feature, such that MCU in our product can talk to nRF9160 via UART interface.
We have found an sample application [Serial LTE...
Hi
I am trying to setup a raspberry pi 4 for flashing nrf devices. But Nrfjprog doesn't seem to work.
I am using a Raspberry Pi 4 with 2021-05-07-raspios-buster-armhf...
Hi,
I noticed that the nRF9160s I2C low level logic voltage is quite high. With a 2kR resistor at 3.3V it's already more than 200mV. Because this is quite high and will...
Hello all,
I am using the BLE app UART code. I m trying to connect one plus through BLE connection. but nordic devkit BLE is not visible.
I am using the default configuration...
Sorry but I find the documentation useless. I don't even know where to start. It could be I have not found the correct documentation which is not surprising.
The best I...
Hi
I've built a USB HCI fimrware based on the sample from the nRF Connect SDK for the nRF52840DK.
See also: (+) HCI USB based on nRF Connect SDK 1.7.0 failed to update...
The SDK version of the program I developed with SES is v1.5.0. Now change the development environment to vscode and import the program into vscode through "add an existing...
Hi,
Is it possible to generate a passkey before initiating the pairing process?
The peripheral in my system does not have a display or input, so I'm looking for a way...
Hello Developers, I am currently developing an application on top of mqtt-sn publisher example. Now i want to add OTA DFU in my mqtt-sn based application. I have started up...
