Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I am trying to port a tested program from NRF52 DK to NRF Thingy. To do the same I had changed the board to PCA20020. After I do that, I program using the NRF52 debug out...
Hi,
If the app keeps sending data at a certain rate, the numbers will skip and the software will stop.
I tried to see how much data I could communicate and at what speed...
In my situation, I want to use ble to designed a piconet which has 1 master and up to 4 slave .( upload(Slave->Master) rate is 2.2KB/s,download(Master->Slave) rate is 500...
Hi
A few questions regarding the "saadc_pca10040" example:
If I read one analog pin then what is the meaning of this matrix of values :
"static nrf_saadc_value_t...
This page shows that MPU is not supported on nRF52840: https://infocenter.nordicsemi.com/topic/sdk_nrf5_v16.0.0/nrfx_drv_supp_matrix.html
On the other hand, the following...
Hello Nordic Experts,
I'd like to add the usb hid composite to one of BLE examples. I followed link below and combined the example usbd_hid_composite with ble_app_blinki_c...
Daer usually we need minutes to lock the LTE cell and connect to the network. There is a way after the connection to save the data (NVM or flash) and on restart to use them...
Hello Everyone,
I am trying to implement fds in nrf52832 with sdk 15.2. getting some issues. I am using 5 record key's and 1 file id.
Before coming to that, Can anyone...
Hello Everyone,
I am using nrf52832 and sdk 15.2 for ota over serial. I have made bootloader for OTA over UART and tested same with nrfutil using my dfu package file. firmware...
Hi. I my embedded code I read default MAC address internally and mine is read as 73:7F:..... but in reality is supposed to be F3:7F.....
I have read few tickets where people...
Hello,
We are designing a custom board, and we would like to use an external crystal for the low frequency clock source, but we are running into disconnect issues. A similar...
Hi,
I have been trying to get the BLE secure DFU example working on a custom board (nrf52840 - BC840 module). I tried it on SDK 15 and SDK 16. When I flash the BLE DFU,...
I am trying to get the current time and the current time zone. I see there is some modem commands LWM2M commands that appear to have the capability to do that. When I try...
Dear all,
I have an application that requires me to keep advertising until the button is pressed.
I use a timer to read the status of the input pin and then if input is...
