Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
nrf52840 17.1.0 s140 SDK :- examples/dfu/secure_bootloader/pca10056_s140_ble_debug
We are using nrf52840 17.1.0 s140 DK secure bootloader with BLE debug. We initialized...
I am at my 15th attempt to download the SDK from Vscode Nordic extension. It keeps failing midway, sometimes after 30mins, for various reasons that are probably related to...
Hi,
I am ultimately trying to move from version 2.3.0 of the sdk to 2.6.1. I have an nrf52_dk board i want to try and test the "different" way that the sdk is now doing...
I am trying to program a QSPI flash with a file system. I have confirmed that my qspi ini is correct as i can read write and erase. I created a small file system on an usb...
Hi Nordic Dev team, I'm using the older nRF SDK in a project that is built using a nRF52840. I have an RTC and a GNSS connected to the nRF52840. I use one of the LP timers...
Hi,
We are ready for the production of the 9161 and we have applied for the IMEI by the nRF cloud. The IMEI we have applied are all 15 and we want to know if the IMEI's...
We developed a custom board with an nRF9161. During board bringup I want to test if the modem can connect via Cellular. I flashed the modem_shell firmware. The modem reports...
In our application, if i enable Softdevice with LF clock Source as RC i get proper timing on interrupts.
If i remove softdevice and just request lf clock manually, the...
Hi All!
I want to procure the nrf9160DK for my project. Can you please guide me that nrf9160 LTE services will work in Pakistan? The cellular mobile operators in Pakistan...
Hello.
I am developing device using nRF52840 and i have question about IO pin usage.
The circuit is currently providing voltage to the A12 pin (Digital I/O), but it is...
We are using nPM1100 along with a STM CPU. When we put the CPU into deep sleep, it takes one minute for the current to go down to 20uA from 500uA.
We were expecting the...
I have a customised bootloader using uart + BL, built from the SDK examples and modified using articles found here. It works - most of the time. The product is a cusom board...
Hi to all,
this is my first public ticket ;)
I would power a nRF52840 on my custom board both with a cell battery (specifically CR2032) and the VBUS provided by the USB...
Hi, 1. After executing nrfjprog --recover command with PCA10040 DK, I read this hex: nRF52832.hex with Programmer
2. What does this program do that causes read protection...
I've been playing around with the advanced_non_blocking_internal_timer example, on my nRF52DK-52832 board using NCS 2.6.0.
I couldn't get it working for what seemed like...
