I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello.
I am developing using nRF5340DK and nRF Connect SDK v2.9.0. I am checking the operation of "Scheduler Server". The registered schedule was changed to inactive, but...
Hello everyone,
I am a college engineering student working on a circuits project, and I need some help. The project is to design a proximity device that sounds an alarm...
Hello,
we are using a Flutter App on iOS and Android.
With iOS the data transfer is as fast as expected, but Android seems to have delay of 2 seconds between the data...
I am adding a bootloader to my project for OTA DFU.
App core and net core update was successful in the 1st stage bootloader configuration, I'm configuring a second stage...
Does the NCS stack + nRF7002 support scanning while connected? I would expect it could, to support handoff, but getting errors.
Using nRF7002-DK and NCS 2.8.0.
Compile...
Hi, I have an issue when I try to install the nRF connect SDK. I am using Linux Fedora 39, trying to isntall SDK v2.5.0. Steps taken so far:
Download and install nRF command...
Hello! I was wondering if there is any advice from trying to get Non-simultaneous firmware updates using sysbuild with the following constraints:
Must update both App...
Hi,
I am having problems getting PSM mode, or at least getting a decent power consumption in PSM mode, because I think the PSM in working properly.
I am using the EVB...
I am using Zephyr to create a program that integrates BLE Mesh and NUS. My goal is to use a sensor_client to read data from a sensor_server, and then send the data, via peripheral_uart...
Need some help with:
nrf5340 - custom board
NO external Flash
DFU over BLE with simultaneous update of both images allowed ( using this devzone concept with static...
I using a BMI323 sensor with address 0x68 on the I2C bus and a custom-made nRF52832 dev kit. when I tried to send some commands to the sensor via I2C, it didn't work.
here...
Hello, I'm writing an application for nRF91 series and I have the functionality mostly working but the "sleep" current is high, about 4-7mA. I assume that this means that...
Hi,
I am currently working with the nRF5340 Audio DKs and have successfully implemented the gateway and handset functionalities.
Now, I want to extend the system by enabling...
With the mcuboot enabled, I'm not being able to disable the boot banners even by doing the below settings in prj.conf file.
CONFIG_NCS_BOOT_BANNER = n
CONFIG_BOOT_BANNER...
Hi!
In our project, we need to send cloud-to-device commands. By "command" I mean a request to do some short action, not a request to change device's configuration/state...
