I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
I was using the AWS-IOT example and all was working until it wasnt. In troubleshooting this, I loaded the modem shell example, to see if it was a network/connection...
Hi everyone,
I implemented nrf5_SDK_17.0.2 ble_app_uart example, so I connected an external device to my nRF52840 DK and I received the data by my android phone.
Now I...
Hi,
I'm using the nRF52840-DK with SDK 17.0.2. I've developed part of my app, and would like to integrate secure OTA reflash for it. I've copied the code at examples/dfu...
Hello,
I am wondering if there is support for secure web sockets (wss:// protocol) together with the NRF52840 and if there are any example available. So far I got communication...
Hello Devzone Community,
To compile nRF Zephyr based applications at the command line normally depends on the meta-tool `west`. `West` has many capabilities and options...
Hey all Trying to understand how to properly build a basic bluetooth example without errors using zephyr between the 2 cores Error: manually cleaning and flashing reading...
Hello,
I use this code for system_off on a nrf52840 custom board. const struct device *button = device_get_binding("GPIO_0"); gpio_pin_interrupt_configure(button, SW0_GPIO_PIN...
nRF52840 Dongle is configured as Sniffer in the right way according to documentation. When sniffing capture on Wireshark is started, only the Advertising packets are captured...
I have a project where I use the nrf9160dk as a gateway between a BLE sensor and LTE.
The hci_lpuart sample is flashed tonrf9160dk_nrf52840 and the nrf9160dk_nrf9160_ns...
I got a Segger J-Link EDU to be use to program my Nordic Thingy 91. I have previously program the device via USB using the NRF Connect Desktop :Programmer. But connecting...
Hello everyone,
I am having an odd problem. I am using an SoC based on the nRF52832 (the ISP1507-AX). I am using ncs v1.7.0 for development. I am trying out a few things...
Hello guys,
I would like to work using nRF52 as my processor to create products in the future, but I heard about Specific Absorption Rate (SAR) testing and that is good...
Hi all, I am a little confused by the requirements for the external GPS antennal options. My board is version 1.0.1.
In this page ( https://devzone.nordicsemi.com/nordic...
