Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi, I am fairly new to the NRF and was wondering if there was a way to increase the sampling rate to 100Hz. I have used the ble_app_uart example to configure this code:
...
Hi,
I am using nrf52832 DK.
SDK17.0.2 and Softdevice S132
I have a ESP32 C3 module as a central device which scans for BLE5 devices.
I have kept the nrf52832 DK...
Hi there,
I was wondering, is there any project or plan to use the nRF9160 as a modem with standard ethernet interface ? The ethernet interface could be either
- RMII...
Hello, I currently have nrf9160 devices deployed running nrf connect sdk v1.3.0 that fails to reboot into the secondary image. It specifically happens when I try to send a...
Hello. I orignally had an expired SIM card that came with my device, so I got a new SIM card to setup with the Thingy:91. These come with an EID of 19 digits, but no ICCID...
The fault was caught by the weak handler, which I think means it was totally not expected.
The trace starts from peer_manager_init() which is part of the Buttonless DFU...
Hi Nordic Team,
I was doing OTA in nrf52840 using Secure DFU ble example in nrf5 sdk. Where i want add some customizations in the code.
1.I wanted to add spis example...
The sample in nrf/samples/event_manager crashes when running on QEMU_x86 with the following output:
I'm using NRF SDK v1.6. Do I need to configure something in KConfig...
Hi Nordic Team,
Can I upgrade the firmware between different softdevice? From s132 to s113
firmware 1: sd: s132_nrf52_7.0.1_softdevice.hex , bootloader: secure bootloader...
The first chip silkscreen for 2050ST ,second chip silkscreen is 2109XN ,third silkscreen is 2052TJ, transmit power configuration for 8dBm actual test from the chip side, test...
Hello,
I'm trying to flash a nRF52840 board (Particle Xenon) with nRF Connect for VSC on macOS.
macOS Big Sur 10.16
Here is my nRF Connect - VS Code environment: ...
Hello,
I am using multiple ADC pins and realized that repeated calls to the ADC give inconsistent data, suggesting that the conversions are not completing before the next...
As far as I understand at the moment only proprietary solutions are available for Mesh DFU and Remote Provisioning.
I assume that Nordic is working on standard solution...
Hello,
After looking at the schematic of the nRF9160 DK and the Thingy:91, I noticed that for the nRF9160 DK there is only one antenna design for LTE, while for the Thingy...
