I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I am using NCS v2.5.1 and working on a project where I need to turn off the system using a button that triggers an interrupt on a GPIO. I want this GPIO to control a load...
Hi Nordic team
Currently I am trying to send a big chunk of data close to 100 KB from my nRF52832 to nRF connect for mobile app in Android phone. I am able to send few bytes...
Objective : Develop a BLE mesh application with nRF52840 as a sensor node. The sensor captures various parameters ( Temp, dissolved Oxygen etc.) and communicates them to relay...
software:ncs 2.5.0
hardware:nrf5340 dk
hi professor,
According to the article at https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/optimizing-power-on-nrf53...
I have found that in Linux, "nrfutil toolchain-manager launch --shell" is starting a process that uses almost 20% of the CPU according to the top utility. I have found this...
I'm trying to make a BLE beacon with Li-Ion battery and Qi wireless charging circuit. NRF52833 works in high-voltage mode (VDDH connected directly to the battery, internal...
nRF connect SDK 2.7.0 CONFIG_CHIP_LAST_FABRIC_REMOVED_ERASE_AND_REBOOT KConfig option is not working, it is not erasing nvs and not rebooting device. Although I have enabled...
Hallo,
I'm using Segger Embedded Studio to program nRF52840. In the Nordic nRF5_SDK there is the ble_app_uart example using S140 softdevice, which is running well. Now I...
I am trying to measure the current consumption on nRF52832 PCA 10040 2.0.0 with PPK 2 (PCA 63100 1.0.1).
I have cut the SB9 and connect the PPK as the picture:
as shown...
Im a bit stuck here.
I have the following code, trying to communicate with a flash memory:
Overlay:
code:
I get the following error message:
error: ...
Dear Nordic, I have developed an application for nRF52811 on nRF52840-DK.
For this i have referred examples -> peripheral -> template_project.
I have followed https...
I just fired up our most recent custom boards with nRF9161-LACA's, and tried to compile modem shell application for RTT.
I noticed the RTT is disabled because HAS_SEGGER_RTT...
I am working nrf52840 with bg96 modem, i have configured quectel_bg9x.c driver to communicate with bg96 modem from nrf52840.
can you provide a sample application on MQTT...
Hello,
I'm experiencing an issue integrating a freestanding Zephyr module with the sysbuild system. The module defines custom boards and projects. When I use the...
Hi
We are the Manufacturer of Smart lighting
We have start new project" Cellular gateway".
We are evaluating the nRF9160 Dk board .
During this we found issue . it...
