I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi , I am using nrf52840 dongle with sniffer firmware which can be found here . I am following that tutorial and when I try to capture zigbee packets in wireshark , it only...
Hi,
It seems like there are many instances of ASSERT/NRFX_ASSERT that execute crucial checks prior to actions like dereferencing pointers, and they perform a reset if the...
Hi,
1-I have successfully developed an app ... \nRF5SDK1702d674dde\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_template. 2-I have set a UART example to send...
Hi,
We have some questions from one of our FW guys regarding the configuration of the UART pin:
I looked at the UARTE driver implementation, it configures the UART Rx...
Hi there,
We currently have ~500 nRF52832 devices running nRF5 SDK (bootloader, S132, application). These devices are updated using the nRF5 SDK Secure Bootloader UART DFU...
Hi,
I would like to know if it is possible to configure the optimization level only the application built on top of Zephyr, and not all the project.
I am trying to debug...
Hi-
We have an application that currently does not use the soft device. Eventually we will want softdevice S113 in our application once we start to add some BLE based...
*** BEGINEER ALERT ***
Just thought I'd throw that alert in, so you are aware you can't assume anything in terms of base level knowledge here! I'm coming from a Cypress...
I'm currently playing around with learning how to code in VCS with nRF Connect. I was watching a series of Youtube instructional videos ( https://www.youtube.com/watch?v=MGsZJpdLtco&list...
Hello,
My colleague and I created ESB prx project based on SDK 1.6.0 version and nrf5340 dk.
And some source codes in ncs/nrf/samples/esb/prx/src folder are changed...
Hello,
I am trying to work on a simple GPIO program for the Thingy:91 which involves reading a pin for sensor inputs (this will be 2 sensors eventually). I have tried to...
nRF Connect V 1.6.0
using samples/zigbee/network_coordinator against a nRF52840, I am trying to commission a larger number of devices to join the network. Currently 24 devices...
Firstly, my english is not good,
I am using nRF52840 and my IDE is Keil uvision 5, i want to know, where is the pins SDL and SDA
I am new developer, and please you can...
I have successfully formed a mesh and sending data in the format as below
" udp send ff03::1 1234 $01 " to udp '1234' socket
" udp send ff03::1 1234 $02 " to udp '1234...
