I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
When I click ACTIONS/Build to build, the executable module(merged.hex) is not created. Now that zephyr/zephyr.elf has been created, the process will finish.
[Environ] nRF...
Hi,
I wanted to characterise the CS accuracy by changing the default parameters in
I get errors when I try to change rtt_type to sounding sequence. I tried both 32 and...
My customer Penguin ID has the following question about HCI USB for the nRF54LM20A. He claims this is only on the old Zephyr stack and not on the new one. Can you please comment...
Hello,
I'm doing some experimentation with nRF54L15DK dev kit.
I connected PPK2 to P6 on the board to measure VDD:nRF current consumed.
The DK is loaded with a release...
I’m working on an nRF5340 project (NCS 2.9.2) with simultaneous multi-image DFU using MCUboot, MCUmgr (SMP over BLE), and external flash (MX25R64, like the DK).
App-core...
Hi
I am moving an application to nRF54L15DK.
SDK is v3.2.2, single core only, no sysbuild.
Whenever I try to debug I get:
-- west flash: using runner nrfutil -- runners...
Hi,
i am developing under NCS 3.2.1.
I would like to if there exist a stand-alone command for creating DFU (nrfutil sub-command or similar) instead of https://github.com...
Hi guys, I have been working with a custom PCB based around the nRF5340 that uses the nPM1100 as the PMIC. I have configured it for 1V8 VOUTB output, fixed VBUS, VTERM high...
Hello, in the design reference it explicitly mentions:
“Important note on C9: The grounding of the C9 capacitor MUST be isolated from ALL ground layers except the bottom...
Hello,
I’ve been using SSD1306 128x64 OLED displays with nRF52840 boards for several years without any issues, building with nRF Connect SDK 2.5.x to 3.1.0. Recently, I...
We have thousands of devices live in production and we sometimes encounter the situation that we cannot restart bluetooth advertising anymore after a connection attempt. ...
Hi, we are investigating some devices in field, and have limited logs to work with. From time to time, we see EMM reports with cause 255. According to nRF9160 AT Commands...
Hello,
I have been following the tutorial for the DECT NR+ Shell (nRF91x1: DECT NR+ Shell). However, I am unable to locate the sample referenced in the documentation:
...
Hello, I try to do work a ism330dhcx on a custom digital board with a custom board in which there is a NRF54L15 microcontroller. The sensor works on other custom board with...
Hi all, I'm currently evaluating a few different vendors, chips and technologies for an idea I've had. It's a wireless+USB gaming HID, so latency is very important. 1kHz polling...
