Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
Hi Support Team
I tested matter bridge sample running on the nRF7002DK with peripheral_lbs sample running on the nRF54L15DK.
Application guide
Then I encountered problems...
I am working with the nRF9160 DK (PCA10090) and would like to use the onboard nRF52840 interface MCU as a host controller for an external peripheral.
From my understanding...
I am using the nPM2100 EK dev board with a stm32wl5MOC.
Using the example from the bare metal drivers, I adapted the code to my board.
I can succesfully read and set bytes...
currently this is more of a theoretical question, but i have an idea of something that might utilize this (3 QSPI devices)
Ive been looking at the Nrf5340 and the nrf7002...
Hi, I am stuck on the BLE channel sounding Initiator initialization. I took the code from the channel sounding connected initiator and integrated into my FW.
Due to unknown...
Hello Nordic Team,
I am using the nRF5340 Audio DK and I want to implement a simple audio loopback — where the board captures voice from the on-board PDM microphone and...
hello~
nPM1304 nominal sleep mode 500nA (it is still uncertain whether the buck converter can operate?)
Can't the sleep mode be lower than 500nA?
best regards
sam
I'm following the Lesson 9, Exercise 2: DFU over USB - Adding External Flash from the Nordic Academy: Tutorial Link
SoC: nrf54l15
SDK version: 3.0.2
Toolchain version...
Hi,
I’m using a custom nRF5340 board , and I recently migrated my project from nRF Connect SDK v2.9.0 to v3.1.1 .
The same project compiled and worked fine on v2.9.0,...
Hello,
I'm interested in nRF54L10 SoC, in Mouser and DigiKey I see that I can buy it in this package: QFN48 (QFAA). However in the datasheet it shows this package QFN40...
Hi,
I’m currently working with the nRF54L15 DK using the Channel Sounding Initiator with Ranging Requestor sample from the latest nRF Connect SDK. The setup runs successfully...
Dear nRF experts.
I am using the radio_test sample with SDK3.10
We used radio_test to add UART commands to control the on/off of all GPIOs for pin verification. We found...
I'm currently looking for a high-speed data transmission and reception solution that requires wifi (NRF7002) throughput, but I don't want to transmit data via wifi. It should...
I'm using nRF Connect for Visual Studio Code, working on a project that has worked great in the past, but I'm getting error messages now when attempting to flash any board...
