The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hi,
I am using NCS 3.2.1 and nRF52840-DK's version 3.0.3.
I flashed 2 boards with the openthread/cli sample.
From the CLI on both boards, I issued the following commands...
I’m trying to transmit a payload of up to 2,450 bytes using CoAP over OpenThread. Before jumping into firmware development, I want to evaluate the feasibility of transmitting...
Hello DevZone,
I have some questions about nPM1300. I know that nPM1300 need a battery pack that already contains a PCM.
When the PCM activate the protection due to overdischarge...
Hi,
I'm using the nRF54L15 (custom board, nRF54L15 DK base) with NCS v3.1.0.
I have two UARTs:
uart30 — Shell/console (needs CONFIG_SHELL_BACKEND_SERIAL=y , which...
Hi,
I'm trying to use an nRF5340 Audio DK to communicate with another board via SPI. The voltage needs to be 1.8v. How do I configure my board to do this?
Hi,
We are using the nRF7002-DK board. I am using Zephyr samples/net/wifi/shell with no other external connection other than the j2 micro-usb connection to PC and with the...
Hi,
We're aware of the modem 2K TLS buffer limitation. It's causing us quite a bit of headache related to the device shadow.
Our application needs a number of config parameters...
Hello,
I am trying to access to two partitions of 2gb each on a micro SD card of 32gb.
I can access to one partition of 32gb in my micro sd card but as it is formatted...
I've been struggling with Thread connectivity on a custom PCB, powered by a MinewSemi ME54BS03 module (with IPEX connector)
I'm using an external 2.4GHz antenna and I'm...
Hi,
I am facing a power consumption issue with the nRF54L15 (BM15C SoC) in deep sleep (System OFF / low-power state). The measured current consumption is approximately 221...
Hi all,
Note that I am using a Fedora Workstation VM on VirtualBox for keeping everything clean. I pass the connected USB development board to the VM. I am trying to evaluate...
Hi ,
I’m working on an nRF5340 using nRF Connect SDK v2.7.99-cs2 . BLE security is configured as Just Works (Security Mode 1, Level 2) on the peripheral .
I’m attempting...
I am using the nRF54L10 on a custom board with a couple of LEDs, a flash storage device and a GNSS device. The application wakes periodically to gather fix information from...
