Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello,
We are seeing a few strange cases of devices reporting MPSL assertion on file 112, line 1588. The assertion comes from the softdevice, so its a bit tricky to understand...
I am currently using the NRF_POWER->GPREGRET and GPREGRET2 registers to store data for my custom handling under NVIC_reset . My objective is to identify the cause of a manual...
I designed a circuit using the NRF54L15 to connect via Bluetooth and control several peripherals. I program the chip using the Debug Out of the NRF54L15 DK Development Kit...
I am able to build the firmware without any errors from persistent_key_usage example as below condition
Board: NORA Evaluation Board SDK Version: 3.1.0 Toolchain: 3.1.0...
Hello Nordic team,
I am using an nRF5340 DK with Zephyr, and I am facing an issue where the UART console freezes whenever CONFIG_LOG_BACKEND_FS=y is enabled.
My logging...
Hello, Nordic,
I am trying to use radio test to do FCC, but when I test the example, I found some issues.
When I test it by nRF connect the input may be truncated or...
Hello.
I'm trying to use WS2812 leds with I2S. I'm using two boards for testing: an NRF5340DK and my board based on the HOLYIOT-21069-5340 module.
I'm using a zephyr/samples...
using ncs 3.1.1 how can we invert SW_CTRL0 logic we using a different RF SWITCH then DK
"Does register 0xA4002DC8 (SLEEP_CTRL_GPIO_CTRL) on nRF7002 have a bit to invert...
nRF5340-DK, PCA10095, v2.0.1 and v2.0.2
According the zephyr device tree, the UART0 is mapped to GPIO 0.19/0.20 and UART1 is mapped to GPIO 1.0/1.1 .
According the schematics...
Dear Nordic,
I got some AT commands here <https://docs.nordicsemi.com/bundle/ref_at_commands_nrf91x1/page/REF/at_commands/production_test/xrftest_tx_set.html> to know that...
Hello Nordic Team,
I am currently working on OTA using Sysbuild configuration on the nRF52833 with the nRF Connect SDK .
In this configuration, I enabled overwrite-only...
I'd really like to be able to set the path to nrfuitl in the extension so I do not have to put int on my system path, but rather keep it contained in my project.
