We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I am new to BLE development and was wondering how I can read the data published by the A&D Medical Blood Pressure Monitor with the nRF5340 acting as a central. I can connect...
hi support team,
customer reported on problem that one product is ok when in factory, but now is in problem after delivered to office.
i had onsite debug and find out...
Hello,
I am practicing the intermediate Nordic Academy online course, and I have a problem of the thread viewer.
I have enabled debug, I did everything strictly according...
We are nRF52840 in one of our products. When we use SYSTEM OFF mode with with hardware design, current consumption is around 3uA but when we use SYSTEM ON mode with RAM retention...
BLE settings:
1) Advertising interval: 500 ms.
2) I am not explicitly turning on the DC-DC regulator; I am using the default settings.
3) Tx payload: 31 bytes.
According...
Dear All:
I have followed the procedure as shown in the following to make a Mesh heartbeat application.
I started with the example of ligtht switch client and server for...
The documentation for CONFIG_MBEDTLS_PEM_CERTIFICATE_FORMAT in nRF Connect SDK says:
By default only DER (binary) format of certificates is supported. Enable this option...
My question is completely wrong (0x2880 is alloc failure, not parsing failure)! Please ignore.
When using the nRF Connect SDK mbedtls implementation to conduct a TLS...
Hi,
For the nRF52840, can we use another pin than P18 to realise the Pin RESET functionnality?
I can write the register NRF_UICR -> PSELRESET with numbers other than the...
Hi Devzone,
I am facing an issue in my application where my device is working as a BLE peripheral advertising for connection. The device stops advertising after connecting...
I'm trying to download and flash an MCUboot image at runtime. All goes well, the image is flashed to the secondary slot, confirmed, and marked for upgrade. The secondary slot...
I use the nrf_dm demo program, when using the nRF52840DK development board, the program can print the log normally.
Then I changed the build configuration to nRF52840Dongle...
This is a continuation of this question . It may be necessary reading to understand the context.
I 'm confused by this topic too, however I think the error about "boot_partition...
Hello,
I have a custom nrf5340 board with a simple firmware flashed on it (turn on red led). My board has a hall sensor as a turn on/off switch (latched). If I connect it...
I used nRF52840 board with SDK 17_1_0 ,
Using FDS I am able to read and write data into flash when nRF52840 board Continuous ON,
But when i Make nRF52840 board Power OFF...