We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
We want to work on BLE mesh topology using nordic nrf-833 boards. We want to implement mobile application in react native to support BLE mesh features. Please let us...
I was using nRF Connect (v3.6.1) to communicate to Segger J-link Base (version 11.0) but it failed. The error message was: ""Failed to setup device: No serial port available...
I want to develop a software that can restore the program after a power failure. I mean, if the device restart, I don't want it to execute from the beginning of the main function...
I made a serial bluetooth function but I want to use it in a form like printf.
Please tell me how to use it using bluetooth_send function.
bluetooth_send("gyroscope...
The reference design for the nRF5340DK uses 0201 components for the matching network.
Would it be acceptable to replace the 201 matching network components to 0402 parts...
Hello NRF,
I have a custom board with NRF52832, and exposed the SWDIO, SWDCLK, GND, VDD, RESET pins for programming the board through the NRF52-DK board.
I started with...
Dear Nordic,
I have some issue with SPI interface (MCU as master, BL654 as slave)
I can see correct signal from oscilloscope, and SPI mode and CLK is config correct...
hello,
i am using nrf52840 with sdk 15 and using ble_app_blinky example i want to advertise my device as i beacon(only mac address) without any name what i did until now...
We have generated a .hex file to be programmed to the external QSPI flash on the QSPI bus of an nRF5340, using the same MX25 part as used on the DVK (8MB/64Mbit) but with...
Hello Team,
Need urgent support for the nRF52840-DK.
I want to develop a program for the above mentioned kit for green power zigbee communication. This DK will communicate...
I was testing 9160 power consumption, the specifications says it is the minimum consumption current 7µA, but when I test on the DK board, the minimum current is 2ma, my test...
Greetings, I designed custom board using nRF52832 and sht20 temperature sensor. I defined sda and scl pin number of sht20 in pca board file (pin number 23 and 24). 4.7k pull...
Hello,
I want to test cold start performance of GPS on the nRF9160 DK using the gps example from the SDK. If I run the example unmodified from the sdk, get a fix, power...
Hello!
I am working on a project where we want over the air updates for the finished product. To make that possible I implemented the buttonless DFU and it is working great...
