I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Using the matter weather station as a base on a thingy53 and SDK 3.1.0 which should use matter 1.4.2 if i open zap-gui and try and add a Control Bridge (0x0840) i get notification...
Hi,
1.Please troubleshoot the issue and identify the cause for no response when sending AT%HWVERSION using the merged_serial_lte_modem_v3.0.0.hex and mfw-pti_nrf91x1_2.3...
Hi,
I am currently working with Trusted Firmware-M (TF-M) on an nRF device and trying to understand the design difference between Internal Trusted Storage (ITS) and Protected...
I have encountered a problem with I2C bus on the nRF54L15. BMP390 sensor is connected to nRF54L15-DK by the i2c bus. if i try to brake the line and recover it agane, the connection...
In nRF5 SDK, we configure GPIO wakeup sources for System OFF using `nrf_gpio_cfg_sense_input(pin_number)`.
What is the **exact equivalent API/configuration** in **nRF Connect...
Hello.
I'm trying to use a nrf52840 as a central device and connect to a gopro13. The connection works a certain number of times. But after a while (several days or maybe...
Hi all,
this is a bit embarrassing, I updated from nrf SDK 2.5.0 to 3.1.1 and I'm a bit lost with the simplest things.
I need to toggle an LED on a custom board. I'm using...
We are using part nRF52840QF (QFN package, not aQFN) as part of new designs as it has the following improvements compared with the nRF52832:
Output power of +8dbm
Extended...
Hi,
I’m having trouble getting the Matter Test Harness to run.
Environment
rPi 5 set up per Matter Test-Harness User Manual.pdf (using project-chip/certification...
Hi, I'm trying to install modem fw using the script given by Sigurd : https://devzone.nordicsemi.com/f/nordic-q-a/53208/updating-nrf9160-modem-firmware-through-the-command...
Hi. I have a new project using zephyr 3.5.0 and ZMK, so I don't think NCS SDK is an option. I am using pca10056/nrf52840dk
I am trying to configure I2S, and the examples...
I am currently experimenting with the nrf9151DK and was hoping to mimic a LTE-M sensor that would wake up once an hour, send a message over CoAP with DTLS, then go back to...
Hello, I have problems in the async-mode with the UART21 output and the nRF54L15. I am using Toolchain v3.1.1 and SDK v3.1.1.
When I use the uart_tx function to print out...
Hi
Is there a specification of running the nRF21540 in Tx mode at 10 dBm and 20 dBm with no load connected? Will the reflected signal cause damage to the PA and if yes,...
Hi Support Team
I tested matter bridge sample running on the nRF7002DK with peripheral_lbs sample running on the nRF54L15DK.
Application guide
Then I encountered problems...
