Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
Hi,
I am working on an FCC cert of our product which is nRF52811 based. We are currently on SDK 2.0.0. I have copied from the nrf samples bluetooth area the projects peripheral_uart...
1.After I burn AP CODE, executing "nrfjprog -f nrf53 --program factory_data.hex –sectorerase" instruction will cause the following error. This issue wasn't happened in prior...
I am trying SPI Master/Slave communication between two nRF54L15-DK boards, using the nRF Connect SDK v2.8.0 and nRF54L15-DK 0.9.1 and 0.8.1. However, it seems that the SPIS...
Hi,
I just got my Thingy91x up and running, and it’s been on for a few hours now, but it has already used 460/500 location requests. How often does the unit send location...
Hi, I am trying to flash to a new design which uses ublox NORA-B120 module. I am trying to flash from vsc. But the flashing fails with following error.
Anyone can help...
Hello,
I have configured 2 nRF5340 boards for LE audio streaming from my mac. Two things I am noticing:
1. The audio is streaming but it is intermittent. Audio plays...
I found out nrf_reset_network_force_off() can be used to turn on/off the network core in firmware, per the example in NCS v2.5.0, samples/subsys/ipc/ipc_service/icmsg . I...
Hi,
I am making an application based on the peripheral-nus example. The checking for CR is removed and all characters are just sent further when available. The problem is...
Hi, I have developed a stable program on the nRF52840 board, and now I'm transporting all the code, and trying to make it compatible with an nRF54L15 board.
I used ZMS to...
Howdy,
I am currently working on the nRF52840 chip and trying to convert my SPIS code from being in my main while loop into being interrupt driven. I am using Zephyr to...
Hi!
I want to integrate power management into our FW. Therefor I did enable it in the prj.conf:
And added runtime enable and action run calls regarding this device...
Hi,
Is there a sample demonstrating the EasyDMA configuration for the I2C21 peripheral of the nRF54L15 using SDK 2.8? I found a sample for the nRF52 with an earlier SDK...
HI,
I am super confused about which direction to go forward...
I need example code and tool chain where I can build a
1) ble bootloader that supports the Nordic Semi...
Hi,
We are using nRF52832 custom board for our application.
In this board we have to use P0.05 pin as GPIO Input. But it is continuously showing LOW signal in multimeter...
