Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
in android program i disconnect from my gat with this code
while(isconnected){
mbluetoothGatt.disconnect();
Log.d(TAG, "Disconnecttodevice: ");
}
mbluetoothGatt...
Hello, I load UART over BLE example on nrf51DK (51422) DK board and measure for 13 seconds from power on.
Here is the result graph and the average current is about 175uAh...
Hello Nordic! In my FW, I need to know when a specific packet has been actually sent (because of SD packet buffering). I am able to receive the BLE_EVT_TX_COMPLETE event,...
Hello I'm using SDK nRF5_SDK_11.0.0_89a8197.zip and I find out that most freeRTOS file version is: "FreeRTOS V8.2.1" but "external\freertos\config\FreeRTOSConfig.h" is in...
Hello,
I am trying to configure my NRF52 dev kit (PCA 10040) to work with pwm using the build-in timer. I used some code from the low_power_pwm example but when I am using...
I am working in a project.The project had defined the manuf_data that it didn't need the company_identifier(bluetooth core 4.0). Is there any way does not show company_identifier...
Hi,
This is a request for all the users to post some details of sensors they are using along with Nordic chips. We will get familiar with 10 most popular sensors that are...
I am trying to build PCA10040 examples but I am getting the following error:
make genhex
Preparing: .hex
/home/me/nrf52/gcc/gcc-arm-none-eabi-4_9-2015q1/bin/arm-none...
Hi guys
I am planning to develop a beacon app, but I am not sure what would be the minimum scanning interval in order to keep the phone's battery drain on a fairly good...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
Hi, there! nRf Toolbox drove me crazy!! can anyone help me?
I flash "s130_nrf51_2.0.0_softdevice.hex" to the pca10028 board.
I compile the bootloader example "nRF5_SDK_11...
Hi,
I'am having an issue with UART using app_uart_fifo.c (SDK 0.9.2). At times I get communication error (usually at attaching and detaching uart connector) and my error...
Hi.
I'm little worried about our bt sensor power consumption.
We are using twi/i2c to communicate with sensors periodically. We are using app timer to trigger these...
I have a custom board that doesn't use the external 32Khz crystal. The engineer that designed it chose to use P0.0 as UART RX. (I know, poor choice.) I have set up a custom_board...
I am using SDK_11 s130. I see APP_ERROR_CHECK(err_code) being used throughout the SDK examples. When err_code is any value other than NRF_SUCCESS, the nRF51-dk board will...
