I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
I'm running the nrf5340_audio_dk and using version 2.6.0-rc1. When connecting one NRF5430 as headset to another NRF5340 gateway, running BIS mode everything works fine. But...
Hi,
We've been working on an IoT device that uses an nRF52840 in a pre-approved module from Moko. We are getting ready for a commercial launch in 2026, but I am very confused...
I have noticed that the dts file includes the configuration for arduinio_spi, along with the corresponding pins associated with spi4. However, I am unsure about how to utilize...
The Bluetooth 6.0 Channel Sounding feature supports multi-antenna functionality. The nRF54L15-DK development board is currently single-antenna. Is there any official documentation...
Hello,
I am wondering how I can enable APPROTECT through UICR with a TFM project. Using ncs2.6.0 and nrf5340. My project makes use of TFM to separate secure and non-secure...
Hello,
I am experiencing an issue with the I2S interface on my nRF5340 DK while using the nRF5340 Audio Unicast Server application with the nRF Connect SDK v3.1.0. I am...
Hi,
I'm trying to test onomondo static profile with a custom board build with an nrf9161 chip. So I've followed onomodo readme, I got an error when i'm trying to build...
Hello,
Im worried i bricked my PPK2, as I had it in ammeter mode possibly reverse VIN/VOUT connections to my DUT.
The DUT is powered over usb externally. I tried to measure...
Jeg har en skoleoppgave i teknologi og forskningslære 1 om CPU-en. I denne oppgaven må jeg stille spørsmål til en virksomhet som er involvert med denne teknologien. Derfor...
Hello,
I am trying to set the TX Power on theThingy:53 to -20 for advertising. However when I check the output files, the Option ` CONFIG_BT_CTLR_TX_PWR_MINUS_20 ` is always...
Hello,
I am planning to use the nRF5340 in High Voltage mode and LDO mode. Currently, I am designing a PCB where minimizing the component count is critical.
I understand...
HI
I previously used the NFC feature in SDK version 3.0.0, which had an abnormal current issue after each trigger. After applying a patch from the forum, this problem was...
I’m designing a PCB using NRF9151-LACA-R7 and an NRF52810-QFAA-QFN48 Our CM needs the exact temperature data for SMT reflow , but we can’t find it clearly in the datasheets...
Hello, I am currently working on development on the nRF54H20DK and the nRF7001 shield. I am yet to find documentation on if these two are capable of sharing a singular antenna...
Hi,
We're trying to preprogram our nRF54L05 SoCs before SMT as this is more efficient in our production process. In the past, we did this successfully with an nRF52810,...
