Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
I am using the IQ values collected from the Channel Sounding example. The data in the 0 section seems to indicate that this channel is not in use? For example, as shown in...
Hi, I see this goes back at least as far as v2.4.4 and still exists in v3.1.1. Around line
if ((!err) && (err != -EALREADY)) { LOG_ERR("Stop LE scan failed (err %d)", err...
nRF52840 datasheets says it supports 3 SPI slaves, but I need 4 SPI slave devices on my next design (the current design uses 2 SPIs). I don't need DMA transfer at this moment...
I am trying to implement Attribute caching as described in Vol 3, part G, section 2.5.2 of the Bluetooth Core Spec .
Reading the GATT Database Hash seems to work:
The...
Hi Nordic team,
I’m working with an nRF9160-based device and have observed inconsistent LTE behavior when the device operates in areas with poor or unstable signal strength...
Hi,
I want to synchronously get data from different nodes.
Can BLE mesh obtain information from multiple nodes simultaneously? I would like the collected data to have...
Hello,
Using nRF Connect vscode extension, vscode is very slow and almost unusable.
The following process is started multiple time and i have an instance taking 100...
I have an issue with the Lightness setup server set cb being triggered without a connected device and is not internally called in my code. Yet for some reason the set cb is...
Hi
I noticed nordic provides Wi-Fi: Throughput to evaluate the throughput when device is working in STA mode.
If I want to evaluate the device in AP mode, is there any...
Hallo, we are evaluating the UART peripheral of the nrf54l15. As a first step, we are trying to get two DK to communicate with each other, unfortunately without success. ...
Hi all,
I'm looking at an issue and I can't get my head around it. I clearly do something wrong here but I'm stuck.
On our nRF54L15 DK we have a program that can show...
Dear Teams,
I’m using an nRF9151DK board running a simple firmware (example link: github.com/.../ subsys /pm/ device_pm ).
I connected a Power Profiler Kit II (PPK2) to...
Hi,
When I was developing, I found that the matter sample is a little different from the Bluetooth sample .
I want to disable CONFIG_THREAD_LOCAL_STORAGE in the Bluetooth...
Using a slightly modified version of the Zigbee Light Bulb sample app from the current samples compiled using nRF Connect for VSCode on a Mac and programmed to a nRF52840DK...
